manualshive.com logo in svg

Epson TP3, Manual, Page: 19 / 96

Share
Download
Epson TP3 Manual Download Page 19

Functions & Installation 2. Specifications 

 

RC700-A option TP3  Rev.8 

9 

(2)  EMERGENCY STOP switch 

When this switch is pushed, the Emergency Stop state is held both mechanically and 
electrically.    Pushing the switch stops the program, removes power to robot motors 
and stops the manipulator motion immediately. 
To cancel the Emergency Stop state, first turn the EMERGENCY STOP switch to the 
right  to release the mechanical latch.  Switch  the mode selector key switch  to 
“Teach”.  Press the <Reset> key to reset the electrically held Emergency Stop state.  
The E-STOP lamp goes OFF. 
For the procedure to reset the EMERGENCY STOP switch,  refer to 

Functions  & 

Installation 1.3 EMERGENCY STOP

. 

(3)  Touch Panel 

The touch panel is used to display various kinds of information, select the functions, 
and enter the setting values. 

(4)  Jog Key / EXE. Key 

The keys are used for teaching operation and command execution. 

(5)  Connection Cable 

This cable is used to connect the Teach Pendant and the Controller. 
The connector is attached at the end of the cable. 

(6)  Handle 

The handle is used to support the Teach Pendant by an arm.    To hold the handle, grip 
either one of the parts with raised bumps which are located on right and left of the 
handle. 

(7)  Touch pen 

The touch pen is used to operate the touch panel. 

(8)  Enable switch 

This is a three-position switch (right-handed/ left-handed).  To operate the robot in 
the TEACH mode, grip either right- or left-hand switch and use the jog keys.   
When operating the robot in the test mode, set the switch to ON position. 
The switch turns ON when it is at the midpoint, and it turns OFF when it is fully 
gripped or released. 

(9)  USB port protection cover 

This is a cover for the USB port. 
The cover can be removed by holding and lightly pulling the thin part at the tip. 

 

CAUTION

 

■

  Make sure to set the cover to protect the USB port when the USB port is not used. 

(10) USB port 

The port for connecting the USB memories. 

 

Summary of Contents for TP3

































































































Reviews:

No comments