background image

2. Installation 

 

Safety and Installation (T, VT / EPSON RC+ 7.0) Rev.15 

61

 

2.5.2  Safety Door Switch 

 

WARNING 

 

The interlock of the Safety Door must be functioning when the robot 
system is operated.  Do not operate the system under the condition 
that the switch cannot be turned ON/OFF (e.g. covering the switch with 
tape).    Operating the robot system when the switch is not functioning 
properly  is extremely hazardous and may  cause  serious safety 
problems as the Safety Door input cannot fulfill its intended function. 

In order to maintain a safe working zone, a safeguard must be set up around the 

Manipulator.  The safeguard must have an interlock switch at the entrance to the 

working zone.  The Safety Door that is described  in this manual is one of the 

safeguards and an interlock of the Safety Door is called a Safety Door switch.  

Connect  the Safety Door switch to the Safety Door input terminal on the 

EMERGENCY connector. 
The Safety Door switch has  safety features such as temporary hold-up of the 

program or the operation-prohibited status that are activated whenever the Safety 

Door is opened. 
Observe the following in designing the Safety Door switch and the Safety Door. 

-  For the Safety Door switch, select a switch that opens as the Safety Door opens, 

and not by the spring of the switch itself. 

-  The signal from the Safety Door (Safety Door input) is designed to input to two 

redundant signals.   If the signals at the two inputs differ by two seconds or 

more, the system regards it as a critical error.  Therefore, make sure that the 

Safety Door switch has two separate redundant circuits and that each connects 

to the specified pins at the EMERGENCY connector on the Controller. 

-  The Safety Door must be designed and installed so that it does not close 

accidentally. 

 

 

Summary of Contents for T3 Series

































































































































Reviews: