Epson Stylus Color 670 Service Manual Download Page 41 | Manualshive

Page: 41 / 152

background image

EPSON Stylus COLOR 670

Revision A

Operating Principles

Overview

41

2.1.7 Capping Mechanism

The Capping mechanism covers the Printheads with the cap holder to prevent
the ink around the nozzles from increasing viscosity when the printer is in
stand-by mode or when the printer is off.

Capping mechanism moves up when the CR unit moves to the right end of
the CR guide shaft and covers the printhead nozzle plate.

Stylus COLOR 660 has built-in air valves in the capping unit but Stylus
COLOR 670 uses valveless system.

Air valve function used for the previous models pumps and ejects ink only
inside the cap by sucking ink with the valve open. Valveless system is
developed by changing the ink sequence.

When sucking ink only inside the cap (false absorption), this printer moves
printhead to the left from the cap unit (out of the cap) and drives pump to
perform false absorption.

Figure 2-10. Valveless Capping Mechanism

Negative pressure

Ink Eject Valve

Valve

Released state
The absorbing
power is low.

Closed state

Flags for
Frame

Flag for Carriage

Ink Eject Valve
Negative pressure

Flag for Carriage

Air valve is not assembled
in this portion.

Stylus COLOR 660

EPSON Stylus COLOR 670

«
...
39
40
41
42
43
...
»

Summary of Contents for Stylus Color 670

























































































































































Reviews:

No comments

Related manuals for Stylus Color 670

Brand: Makita Pages: 16

Brand: ICS Pages: 20

Brand: Velleman Pages: 9

Brand: AP&T Pages: 3

Brand: Malibu Boats Pages: 2

Brand: Hakko Electronics Pages: 2

Brand: Delta Elektronika Pages: 21

Brand: Parkside Pages: 160

KH 3041 AIR STAPLER SET

Brand: Parkside Pages: 37

Brand: Pulsar Pages: 3

TOTAL ACCESS 4303 PLUS

Brand: ADTRAN Pages: 2

Brand: Hilti Pages: 112

CJS 20V/80 PLUS

Brand: F.F. Group Pages: 56

Brand: Bahco Pages: 9

Fatality FTY550W

Brand: OCZ Pages: 21

Brand: Facom Pages: 2

Brand: BorMann Pages: 44

Brand: Kyocera Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands