Epson Stylus Color 670 Service Manual Download Page 85

Page: 85 / 152

EPSON Stylus COLOR 670

Revision A

Disassembly and Assembly

Disassembly

4.2.5.5 ASF Assembly Removal

Remove the Housing. (See “Housing Removal” on page 72)

Release the hook and remove the Spur Gear 34 from the Roller Shaft of
the ASF Assembly.

Figure 4-21. Spur Gear 34

Remove the cable from the Cable Hook of the ASF Assembly.
(The Cable Hook is located at the right side seen from the back side of the
printer.)

Remove 1 screw (with washer) securing the ASF Assembly to the Printer
Mechanism and ASF securing screw.

Figure 4-22. ASF Securing Screw Removal

Shift the ASF Assembly to the right (seen from the back side of the
printer) and while lifting the Sub Paper Support, remove the ASF
Assembly to the back side of the printer.

Figure 4-23. ASF Assembly Removal

Spur Gear 34 Securing Hook

Cable Hook

Spur Gear 34

Securing Screw with Washer

ASF Securing Screw

Sub Paper Support

Shift the ASF to the right

Summary of Contents for Stylus Color 670

























































































































































Search results

Summary of Contents for Stylus Color 670

Reviews:

Related manuals for Stylus Color 670

Brands by name

Popular brands

Epson Stylus Color 670, Service Manual

Search results

Summary of Contents for Stylus Color 670

Reviews:

Related manuals for Stylus Color 670

Brands by name

Popular brands