Epson Stylus Color 670 Service Manual Download Page 100

Page: 100 / 152

EPSON Stylus COLOR 670

Revision A

Adjustment

Overview

100

5.1 Overview

This section describes the procedure for adjustments required when the
printer is disassembled and assembled for repair or service.

5.1.1 Required Adjustments

Table 5-1 lists all the necessary adjustments for this printer. If any service
listed in this table is carried out, all adjustments corresponding to that
service should be performed to ensure proper operation of the printer.

Table 5-1. Required Adjustments

Performance Priority

Service/Replacing parts

PG Adjustment

Initial Ink Charge

Head ID Setting

Head Angular

Adjustment

Bi-D Adjustment

USB ID Input

Replacing the printer mechanism.

Replacing the Main Board.

Replacing the printhead unit.

Replacing the CR motor.

Replacing or removing the CR
assembly.

NOTE: “

”: Required Adjustment. The number in the circle shows the required adjustment order.

“NA”: Not applicable.

NOTE: *: When the CR assembly is replaced with a new one, Head Angular Adjustment is required. When the CR assembly is removed but not

replaced, only PG Adjustment and Bi-D Adjustment are required.

Summary of Contents for Stylus Color 670

























































































































































Search results

Summary of Contents for Stylus Color 670

Reviews:

Related manuals for Stylus Color 670

Brands by name

Popular brands

Epson Stylus Color 670, Service Manual

Search results

Summary of Contents for Stylus Color 670

Reviews:

Related manuals for Stylus Color 670

Brands by name

Popular brands