Epson S1C33210 Technical Manual Download Page 300 | Manualshive

Page: 300 / 559

background image

III PERIPHERAL BLOCK: LOW-SPEED (OSC1) OSCILLATION CIRCUIT

B-III-6-4

EPSON

S1C33210 FUNCTION PART

Power-Control Register Protection Flag

The power-control register (SOSC1, SOSC3, CLKCHG, CLKDT[1:0]) at address 0x40180, which is used to
control the oscillation circuits and the CPU operating clock, is normally disabled against writing in order to prevent
it from malfunctioning due to unnecessary writing.
To enable this register for writing, the power-control register protection flag CLGP[7:0] (D[7:0]) / Power-control
protection register (0x4019E) must be set to "0b10010110". Note that this setting allows for the power-control
register (0x40180) to be written to only once, so all bits of CLGP[7:0] are cleared to "0" when this address is written
to. Therefore, CLGP[7:0] must be set to "0b10010110" each time the power-control register (0x40180) is written to.
The flag CLGP[7:0] does not affect the readout from the power-control register (0x40180).

Operation in Standby Mode

In HALT mode, which is entered by executing the halt instruction, the low-speed (OSC1) oscillation circuits retains
its status before HALT mode is entered. Under normal conditions, therefore, there is no need to control the
oscillation circuit before entering or after exiting HALT mode.

The low-speed (OSC1) oscillation circuit does not stop operating in SLEEP mode set by executing the slp (sleep)
instruction. Therefore, if the CPU was operating using the OSC1 clock before SLEEP mode was entered, the CPU
keeps operating using the OSC1 clock in SLEEP mode.

OSC1 Clock Output to External Devices

The low-speed (OSC1) oscillation clock can be output from the FOSC1 (P14) pin to external devices.

Table 6.2 OSC1 Clock Output Pin

Pin name

I/O

Function

Function select bit

P14/FOSC1/
DCLK

I/O I/O port / Low-speed (OSC1) oscillation

clock output / DCLK signal output

CFP14(D4) / P1 function select register (0x402D4)
CFEX0 (D0) / Port function extension register (0x402DF)

Setting the clock output pin

The pin used to output the OSC1 clock to external devices is shared with the P14 I/O port and the debug clock
signal DCLK.
At cold start, it is set for the DCLK signal output (CFP14 = "0" and CFEX0 = "1"). When using the clock
output function, write "1" to CFP14 and "0" to CFEX0 (refer to "I/O Ports"), and also write "1" to IOC14
(0x402D6/D4).
At hot start, the pin retains its pre-reset status.

Output control

To start clock output, write "1" to PF1ON (D0) / Clock option register (0x40190). The clock output is stopped
by writing "0".
At initial reset, PF1ON is set to "0" (output disabled).

PF1ON register

FOSC1(P14) pin output

0

0

V

DD

V

SS

1

Figure 6.3 OSC1 Clock Output

«
...
298
299
300
301
302
...
»

Summary of Contents for S1C33210
















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S1C33210

Brand: Data Translation Pages: 60

Brand: F5 Pages: 2

Brand: F5 Pages: 90

Brand: F5 Pages: 47

Brand: GAMDIAS Pages: 15

tBOX330-870-FL Series

Brand: AXIOMTEK Pages: 2

Brand: Funkwerk Pages: 2

Brand: Maxim Pages: 14

Brand: RAK Pages: 30

Brand: u-blox Pages: 29

Brand: ZALMAN Pages: 11

LinkStation Mini

Brand: Buffalo Pages: 71

Brand: Lutron Electronics Pages: 4

airMAX NanoBridge M NBM3

Brand: Ubiquiti Pages: 24

SmartRack SR25UBEXP

Brand: Tripp Lite Pages: 4

Brand: Intel Pages: 578

Brand: Cypress Semiconductor Pages: 26

Brand: H3C Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands