Epson PERFECTION V10 Service Manual Download | Manualshive

Page: 33 / 77

background image

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly Procedure

33

4.2 Disassembly Procedure

This section illustrates how to remove the main components of this product. Unless otherwise specified, the reassembly procedure is the reverse of the disassembly procedure. For
additional assembly illustrations, refer to the exploded diagrams provided by SPI (Service Parts Information).

The following flowchart shows the disassembling procedure step-by-step. When disassembling any unit, refer to the corresponding page number shown in the following figure.

Figure 4-1. Perfection V10/V100 Photo/V350 Photo Disassembly/Reassembly Flowchart

Document Cover(P.35)

Upper Housing(P.35)

Carriage Unit(P.41)

CR Motor(P.39)

Main Board(P.37)

Hinge(P.36)

Driven Pulley(P.41)

Harness TPU/TPU Inverter

Board(P.44)

Panel Board(P.37)

Lamp Assy(P.45)

Harness AFL/AFL Main

Board(P.47)

Separation of AFL Upper

Housing Assy/AFL Lower

Housing Assy(P.46)

Start

Disassembly of Main Unit

Start

Start

Disassembly of TPU

(Perfection V100 Photo/V200 Photo)

Disassembly of AFL

(Perfection V350 Photo)

TPU Upper Housing(P.43)

AFL Inverter Board/AFL

Inverter Board Cover(P.48)

Film Ejection Cover(P.51)

Cover Lower Assy/AFL

Sensor A(P.51)

AFL Sensor B(P.50)

Film Holder Lock(P.54)

Damper/Film Holder(P.53)

Eject Button(P.55)

Lamp Assy(P.49)

Hinge Disengagement(P.34)

«
...
31
32
33
34
35
...
»

Summary of Contents for PERFECTION V10














































































Reviews:

No comments

Related manuals for PERFECTION V10

IS4320 ScanGlove

Brand: Metrologic Pages: 48

Brand: Cobra Pages: 9

Magicscan MS802

Brand: Conrad Pages: 4

Pannoramic DESK II

Brand: 3DHISTECH Ltd. Pages: 82

Brand: Nikon Pages: 36

Brand: Raven Pages: 34

Brand: POSIFLEX Pages: 24

Brand: Xerox Pages: 77

Brand: Wasp Pages: 12

Brand: Datalogic Pages: 3

Bearcat UBC144XLT

Brand: Uniden Pages: 20

Brand: Launch Pages: 161

Brand: Fujitsu Pages: 4

Brand: Fujitsu Pages: 449

ScanSnap Organizer

Brand: Fujitsu Pages: 81

Brand: Fujitsu Pages: 2

Brand: Fujitsu Pages: 320

Brand: Fujitsu Pages: 485

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands