Epson PERFECTION V10 Service Manual Download

Page: 44 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of TPU

4.4.2 Harness TPU/TPU Inverter Board

1. Remove the TPU Upper Housing.

(4.4.1 TPU Upper Housing on page 43)

2. Disconnect CN8 connector from the Main Board in the scanner Main Unit.

(4.3.6 Main Board on page 37)

3. Disconnect CN2 connector from the TPU Inverter Board, and remove the Harness

TPU from the TPU Lower Housing.

4. Remove the Cover Sheet.

Figure 4-27. Remove the Harness TPU

CN2

TPU Inverter Board

(under the Cover Sheet)

Harness TPU

TPU Lower Housing

Cover Sheet

Reassemble the Harness TPU following the steps below.

1. Insert the Stopper of the Harness TPU into the socket of the

TPU Lower Housing. Make sure that the “T” mark on the
stopper facing upwards.

2. Set the Expansion Tube of the Harness TPU into the holder of

the TPU Lower Housing.

3. Route the Harness TPU through the three notches of the TPU

Lower Housing.

Figure 4-28. Installing the Harness TPU

Stopper

“T” mark

Expansion Tube

Socket

Holder

Notch

Harness TPU

Summary of Contents for PERFECTION V10














































































Search results

Summary of Contents for PERFECTION V10

Reviews:

Related manuals for PERFECTION V10

Brands by name

Popular brands

Epson PERFECTION V10, Service Manual

Search results

Summary of Contents for PERFECTION V10

Reviews:

Related manuals for PERFECTION V10

Brands by name

Popular brands