Epson PERFECTION V10 Service Manual Download

Page: 41 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of Main Unit

4.3.8 Driven Pulley

1. Remove the Upper Housing.

(4.3.3 Upper Housing on page 35)

2. Remove the two screws (C.B.P. 3x8, 5-7 kgf.cm) that secure the Driven Pulley.

3. Remove the Timing Belt from the Driven Pulley, and remove the Driven Pulley

from the Lower Housing.

Figure 4-19. Removing the Driven Pulley

4.3.9 Carriage Unit

1. Remove the Main Board.

(4.3.6 Main Board on page 37)

2. Remove the CR Motor.

(4.3.7 CR Motor on page 39)

3. Remove the Driven Pulley.

(4.3.8 Driven Pulley on page 41)

4. Remove the Carriage FFC that is secured to the Lower Housing with double-sided

tape, and release the Carriage FFC from the rib of the Lower Housing.

Figure 4-20. Removing the Carriage FFC

After replacing the Driven Pulley, make sure to apply G-45
grease to the specified area.

(Chapter 6 "MAINTENANCE"

P58)

When installing the Driven Pulley, match the guide pin and the
positioning hole.

C.B.P. 3x8

Timing Belt

Driven Pulley

Lower Housing

Guide pin and

positioning hole

Route the Carriage FFC through the ribs of the Lower Housing
and secure with double-sided tape, referring to figure 4-20.

Rib

Carriage FFC

Double-sided tape position

Carriage Unit

Lower Housing

Summary of Contents for PERFECTION V10














































































Search results

Summary of Contents for PERFECTION V10

Reviews:

Related manuals for PERFECTION V10

Brands by name

Popular brands

Epson PERFECTION V10, Service Manual

Search results

Summary of Contents for PERFECTION V10

Reviews:

Related manuals for PERFECTION V10

Brands by name

Popular brands