Epson PERFECTION V10 Service Manual Download | Manualshive

Page: 34 / 77

background image

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of Main Unit

34

4.3 Disassembly of Main Unit

4.3.1 Hinge Disengagement

1. Open the Document Cover/TPU Unit/AFL Unit.

2. Hold and lift the Document Cover/TPU Unit/AFL Unit upward, and place it

horizontally.

Figure 4-2. Disengagement of the hinge (1)

3. Push the Document Cover/TPU Unit/AFL Unit towards the main unit, releasing

the 2 shafts from the hooks of the Hinge one by one.

Figure 4-3. Disengagement of the hinge (2)

C A U T I O N

When disengaging the Hinge, the Document Cover/TPU Unit/AFL
Unit may hit the scanner main unit and damage it. Place cushioning
material such as a cloth to the Hinge side of the scanner main unit
during operation to avoid damage.

C H E C K

P O I N T

Disengaging method of the Hinge, to remove the Document Cover/
TPU/AFL from the scanner main unit is common for Perfection
V10/V100 Photo/V200 Photo/V350 Photo. When removing the
Document Cover/TPU/AFL from the scanner main unit, follow the
procedure described below.

Document Cover/

TPU Unit/

AFL Unit

Hinge

Document Cover/TPU Unit/AFL Unit

Hook

Shaft

Before release

Hinge

Hook

Shaft

After release

Hinge

«
...
32
33
34
35
36
...
»

Summary of Contents for PERFECTION V10














































































Reviews:

No comments

Related manuals for PERFECTION V10

Brand: Janam Pages: 2

OneTouch 9420 USB

Brand: Visioneer Pages: 2

OK 300 Hybrid Color

Brand: Zeutschel Pages: 68

Brand: Microtek Pages: 8

Contex SD4400 Series

Brand: BERTL Pages: 29

Brand: DAVID Pages: 26

DocuScan C3200A

Brand: Fuji Xerox Pages: 114

Brand: it Pages: 16

SmartCompact 1D

Brand: SmarTerminal Pages: 80

Brand: Rollei Pages: 36

Brand: Xerox Pages: 70

Travel Scanner 150

Brand: Xerox Pages: 194

Brand: UMAX Technologies Pages: 21

Brand: UMAX Technologies Pages: 38

MultiScanner OneStep HD800

Brand: Zircon Pages: 4

Brand: Uniden Pages: 40

Brand: Cambridge Technology Pages: 17

Brand: Acer Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands