Epson PERFECTION V10 Service Manual Download

Page: 45 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of TPU

5. Disconnect CN1 connector from the TPU Inverter Board.

6. Remove the screw (C.B.P 3x8, 5-7 kgf.) that secures the TPU Inverter Board, and

remove the TPU Inverter Board.

Figure 4-29. Removing the TPU Inverter Board

4.4.3 Lamp Assy

1. Remove the TPU Upper Housing.

(4.4.1 TPU Upper Housing on page 43)

2. Disconnect CN1 connector from the TPU Inverter Board.

(Figure 4-29 on page 45 )

3. Press part A of the Glass Stopper, and remove the two Glass Stoppers.

4. Slide the Lamp Assy in the direction of the arrow to release it from the four hooks,

and remove the Lamp Assy.

Figure 4-30. Removing the Lamp Assy

C.B.P. 3x8

CN1

TPU Inverter

Board

Route the cables of the Lamp Assy through the ribs of the TPU
Lower Housing as shown in figure 4-30.

Hook

Lamp Assy

Glass Stopper

Rib

Glass Stopper

TPU Lower

Housing

Part A

Summary of Contents for PERFECTION V10














































































Search results

Summary of Contents for PERFECTION V10

Reviews:

Related manuals for PERFECTION V10

Brands by name

Popular brands

Epson PERFECTION V10, Service Manual

Search results

Summary of Contents for PERFECTION V10

Reviews:

Related manuals for PERFECTION V10

Brands by name

Popular brands