Epson PERFECTION V10 Service Manual Download

Page: 47 / 77

EPSON Perfection V10/V100 Photo/V200 Photo/V350 Photo

Revision B

DISASSEMBLY/ASSEMBLY

Disassembly of AFL

4.5.2 Harness AFL/AFL Main Board

1. Separate the AFL Upper Housing Assy/AFL Lower Housing Assy.

(4.5.1 Separation of AFL Upper Housing Assy/AFL Lower Housing Assy on page
46)

2. Remove the Harness AFL following the steps below.

1. Disengage the earth cable, that is a part of the Harness AFL from the Upper

Main Board Shield Plate.

(4.3.6 Main Board on page 37)

2. Disconnect CN5 connector from the Main Board of the scanner Main Unit.

(4.3.6 Main Board on page 37)

3. Disconnect CN1 connector from the AFL Main Board.
4. Remove the screw (C.B.P. 3x8, 5-7 kgf.cm.) that secures the earth cable, and

remove the Harness AFL from the AFL Lower Housing.

Figure 4-34. Removing the Harness AFL

3. Remove the screw (C.B.P.3x8, 5-7 kgf.cm) that secures the AFL Main Board and

the AFL Main Board Cover.

4. Disconnect CN2, CN3, CN4, CN6 connectors from the AFL Main Board, and

remove the AFL Main Board and the AFL Main Board Cover.

Figure 4-36. Removing the AFL Main Board

CN1

C.B.P. 3x8

AFL Lower Housing

AFL Main Board

Harness AFL

When installing the Harness AFL, insert the Stopper with the
stopper’s chipped side facing upwards into the socket of the AFL
Lower Housing.

Figure 4-35. Installing the Harness AFL

Chipped side

Harness AFL

Socket

Stopper

C.B.P. 3x8

AFL Main Board

Cover

AFL Main

Board

CN3

CN4

CN2

CN6

Summary of Contents for PERFECTION V10














































































Search results

Summary of Contents for PERFECTION V10

Reviews:

Related manuals for PERFECTION V10

Brands by name

Popular brands

Epson PERFECTION V10, Service Manual

Search results

Summary of Contents for PERFECTION V10

Reviews:

Related manuals for PERFECTION V10

Brands by name

Popular brands