envea M-Sens WR3 Operating Instructions Manual Download Page 8 | Manualshive

Page: 8 / 36

envea M-Sens WR3 Operating Instructions Manual Download Page 8

6

3. Safety

The measuring system M-Sens WR3 designed and built according the latest technology has been
tested to be safe and was shipped in safe condition. Nevertheless persons or objects may be
endangered by components of the system if these are operated in an inexpert manner.

The operating instructions must therefore be read in its entirety, and the safety instructions must be
adhered to. If the device is used in a way that does not adhere to its intended and/or proper use, any
liability or warranty on the part of the manufacturer is void.

3.1 Regular use

•

Only original spare parts and accessories of ENVEA Process must be used.

3.2 Identification of dangers

•

Possible dangers when using the measuring system are marked by the following symbols in
the operating instructions:

Warning!

•

This symbol in the operating instructions marks actions, which may represent a danger for
life and limb of persons when carried out in an inexpert manner.

Attention!

•

All actions which may endanger objects are marked with this symbol in the operating
instructions.

3.3 Operational safety

•

The measuring system must be installed by trained and authorized personnel only.

•

Switch of the power supply for all maintenance, cleaning or inspection works on the tubes
or on components of the M-Sens WR3. Follow the notes of the chapter maintenance.

•

Sensor must be removed from the installation place before any welding work in the area.

•

The components and electrical connections must be checked for damages regularly.
If a damage is found, it is to repaired before further operation of the instruments.

3.4 Technical progress

•

ENVEA Process reserves the right to adapt technical data to the technical progress without
particular advance notice. If you have any questions, ENVEA Process will be pleased to
inform you on possible changes and extensions of the operating instructions.

«
...
6
7
8
9
10
...
»

Summary of Contents for M-Sens WR3





































Reviews:

No comments