Installing Optional Mini-GBICs
Matrix DFE-Diamond Series Installation Guide 3-5
Figure 3-3 Mini-GBIC with RJ45 Connector
Removing the Mini-GBIC
To
remove
a
Mini
‐
GBIC
from
a
port
slot,
proceed
as
follows:
1.
Attach
the
antistatic
wrist
strap
(refer
to
the
instructions
in
the
antistatic
wrist
strap
package)
before
removing
the
Mini
‐
GBIC.
2.
Remove
the
cables
connected
to
the
Mini
‐
GBIC.
3.
Release
the
Mini
‐
GBIC
from
the
port
slot.
Refer
back
to
the
appropriate
figure
listed
below
to
locate
the
release
mechanism
and
proceed
as
instructed.
–
For
the
type
of
Mini
‐
GBIC
shown
in
Figure 3
‐
1
,
push
in
on
the
release
tab
as
far
as
it
will
go
to
release
the
Mini
‐
GBIC.
–
For
the
type
of
Mini
‐
GBIC
shown
in
Figure 3
‐
2
,
pull
out
on
the
release
tab
to
release
the
Mini
‐
GBIC.
–
For
the
type
of
Mini
‐
GBIC
shown
in
Figure 3
‐
3
,
pull
down
on
the
wire
handle
to
release
the
Mini
‐
GBIC.
4.
Grasp
the
sides
of
the
Mini
‐
GBIC
and
pull
it
straight
out
of
the
port
slot.
If
storing
or
shipping
the
Mini
‐
GBIC,
insert
its
dust
protector
to
protect
its
fiber
‐
optic
ports.
1
Mini-GBIC
(MGBIC-02)
4
Port slot
2
Mini-GBIC, top side
5
Wire-handle release
3
7-Pin edge connector (insertion side)
Caution:
Do NOT remove a Mini-GBIC from a slot without releasing the locking tab located under
the front bottom end of the Mini-GBIC
.
This can damage the Mini-GBIC.
The Mini-GBIC and its host device are sensitive to static discharges. Use an antistatic wrist strap
and observe all static precautions during this procedure. Failure to do so could result in damaging
the Mini-GBIC or host device. Always leave the Mini-GBIC in the antistatic bag or an equivalent
antistatic container when not installed.
Precaución:
NO quite el Mini- GBIC de la ranura sin antes abrir la traba ubicada en la parte
frontal del Mini- GBIC.
Si lo hace, puede dañar el Mini- GBIC, puesto que es muy sensible a las descargas de
electricidad estática, al igual que el dispositivo host. Utilice la pulsera antiestática y tome todas las
precauciones necesarias durante este procedimiento. Si no lo hace, pude dañar el Mini- GBIC o
el dispositivo host. Mientras no esté instalado, mantenga el Mini- GBIC en su bolsa antiestática o
en cualquier otro recipiente antiestático.
Ã
Â
Ä
À
Á
Summary of Contents for Matrix 7GR4202-30
