Installing Optional Mini-GBICs
Matrix DFE-Diamond Series Installation Guide 3-3
Installing Optional Mini-GBICs
This
section
describes
how
to
install
a
Mini
‐
GBIC
in
any
of
the
7GR4270
‐
12
front
panel
ports
(1
‐
12)
or
the
7GR4280
‐
19
front
panel
ports
(1
‐
18)
or
in
an
optional
NEM.
For
a
list
of
supported
Mini
‐
GBICs
and
their
specifications,
refer
to
“
Mini
‐
GBIC
Input/Output
Specifications
”
on
page A
‐
3.
Preparation
Before
installing
the
Mini
‐
GBIC,
proceed
as
follows:
1.
Attach
the
antistatic
wrist
strap
(refer
to
the
instructions
in
the
antistatic
wrist
strap
package)
before
removing
the
Mini
‐
GBIC
from
the
antistatic
packaging.
2.
Remove
the
Mini
‐
GBIC
from
the
packaging.
3.
If
there
is
a
protective
dust
cover
(see
in
Figure 3
‐
1
or
Figure 3
‐
2
)
on
the
Mini
‐
GBIC
port,
do
not
remove
it
at
this
time.
Installation
To
install
a
Mini
‐
GBIC
with
an
MT
‐
RJ
connection,
refer
to
Figure 3
‐
1
,
for
an
LC
connection,
refer
to
Figure 3
‐
2
,
or
for
an
RJ45
connection,
refer
to
Figure 3
‐
3
,
and
proceed
as
follows:
1.
Hold
the
Mini
‐
GBIC
with
its
top
side
facing
up
and
its
7
‐
pin
edge
connector
facing
the
port
slot.
2.
Carefully
align
the
Mini
‐
GBIC
with
the
port
slot.
3.
Push
the
Mini
‐
GBIC
into
the
port
slot
until
the
Mini
‐
GBIC
“clicks”
and
locks
into
place.
Warning:
Fiber-optic Mini-GBICs use Class 1 lasers. Do not use optical instruments to view the
laser output. The use of optical instruments to view laser output increases eye hazard. When
viewing the output optical port, power must be removed from the network adapter.
Advertencia:
Los Mini-GBICS de fibra optica usan lasers de clase 1. No se debe usar
instrumentos opticos para ver la potencia laser El uso de los instrumentos opticos para ver la
potencia laser incrementa el riesgo a los ojos. Cuando vean el puerto de la potencia optica, la
corriente debe ser removida del adaptador de la red.
Warnhinweis:
Mini-GBICs mit Fiber-Optik Technologie benutzen Laser der Klasse 1. Benutzen sie
keinesfalls optische Hilfsmittel, um die Funktion des Lasers zu überprüfen. Solche Hilfsmittel
erhöhen die Gefahr von Sehschäden. Wenn sie den optischen Port überprüfen möchten stellen Sie
sicher, dass die Komponente von der Spannungsversorgung getrennt ist.
Caution:
Carefully follow the instructions in this manual to avoid damaging the Mini-GBIC, NEM,
and DFE module.
The Mini-GBIC, NEM, and DFE module are sensitive to static discharges. Use an antistatic wrist
strap and observe all static precautions during this procedure. Failure to do so could result in
damage to the Mini-GBIC, NEM, and DFE module. Always leave the Mini-GBIC in the antistatic bag
or an equivalent antistatic container when not installed.
Precaución:
Siga las instrucciones del manual para no dañar el Mini- GBIC, NEM ni el módulo
DFE, puesto que son muy sensible a las descargas de electricidad estática.
Utilice la pulsera antiestática y tome todas las precauciones necesarias durante este
procedimiento. Si no lo hace, podría dañar el Mini- GBIC, NEM o el módulo DFE. Mientras no esté
instalado, mantenga el Mini- GBIC en su bolsa antiestática o en cualquier otro recipiente
antiestático.
Summary of Contents for Matrix 7GR4202-30
