Endress+Hauser Solitrend MMP40, Operating Instructions Manual

Page: 3 / 36

Solitrend MMP40 Table of contents
Hauser 3
Table of contents
1 About this document . . . . . . . . . . . . . . . . 4
1.1 Document function . . . . . . . . . . . . . . . . . . . . . 4
1.2 Symbols used . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3 Terms and abbreviations . . . . . . . . . . . . . . . . . 6
1.4 Documentation . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Basic safety instructions . . . . . . . . . . . . 7
2.1 Requirements for the personnel . . . . . . . . . . . . 7
2.2 Designated use . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3 Workplace safety . . . . . . . . . . . . . . . . . . . . . . . 8
2.4 Operational safety . . . . . . . . . . . . . . . . . . . . . . 8
2.5 Product safety . . . . . . . . . . . . . . . . . . . . . . . . . 8
3 Product description . . . . . . . . . . . . . . . . . 9
3.1 Product design . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Incoming acceptance and product
identification . . . . . . . . . . . . . . . . . . . . . 10
4.1 Incoming acceptance . . . . . . . . . . . . . . . . . . . 10
4.2 Product identification . . . . . . . . . . . . . . . . . . . 10
4.3 Manufacturer's address . . . . . . . . . . . . . . . . . 10
4.4 Storage, transport . . . . . . . . . . . . . . . . . . . . . 10
5 Installation . . . . . . . . . . . . . . . . . . . . . . . 11
5.1 Installation conditions . . . . . . . . . . . . . . . . . . 11
5.2 Mounting location for round sensor, short /
middle version . . . . . . . . . . . . . . . . . . . . . . . . 11
5.3 Mounting location for round sensor, long
version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.4 Mounting location for rectangular sensor . . . . 13
5.5 Mounting location for rod sensor . . . . . . . . . . 13
5.6 Protection of sensor connector against
abrasion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.7 Post-installation check . . . . . . . . . . . . . . . . . . 15
6 Electrical connection . . . . . . . . . . . . . . 16
6.1 Connection conditions . . . . . . . . . . . . . . . . . . 16
6.2 Cable specification . . . . . . . . . . . . . . . . . . . . . 18
6.3 Electrical connection - example, sensor cable
with 10-pin socket (sensor side) and ferrules
at the end of the cable . . . . . . . . . . . . . . . . . . 19
6.4 Post-connection check . . . . . . . . . . . . . . . . . . 19
7 Operating options . . . . . . . . . . . . . . . . . 20
7.1 Overview of operation options . . . . . . . . . . . . 20
8 Commissioning . . . . . . . . . . . . . . . . . . . . 21
8.1 Analog outputs for measured value output . . . 21
8.2 Operating mode . . . . . . . . . . . . . . . . . . . . . . . 22
8.3 Calibration curves Cal1 to Cal15 . . . . . . . . . . . 23
8.4 Special functions . . . . . . . . . . . . . . . . . . . . . . 24
9 Diagnostics and troubleshooting . . . 26
9.1 Optimizing the material flow . . . . . . . . . . . . . 26
9.2 Difference between measured moisture value
and laboratory value too large during initial
commissioning . . . . . . . . . . . . . . . . . . . . . . . 26
10 Maintenance . . . . . . . . . . . . . . . . . . . . . . 28
10.1 Exterior cleaning . . . . . . . . . . . . . . . . . . . . . . 28
11 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
11.1 General information . . . . . . . . . . . . . . . . . . . 29
11.2 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
11.3 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
12 Accessories . . . . . . . . . . . . . . . . . . . . . . . 30
12.1 Device-specific accessories . . . . . . . . . . . . . . . 30
13 Technical data . . . . . . . . . . . . . . . . . . . . 33
13.1 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
13.2 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
13.3 Performance characteristics . . . . . . . . . . . . . . 33
13.4 Environment . . . . . . . . . . . . . . . . . . . . . . . . . 34
13.5 Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34