Endress+Hauser Nivotester FTR525 Operating Instructions Manual Download Page 59

Page: 59 / 68

Nivotester FTR525

Hauser

Technical data

15�6�3 Material

Housing: plastic PC-GF10

15�6�4 Terminals

• Screw terminals, plug-in

• 2,5 mm

(14 AWG)

• 0.14 to 2.5 mm

(26 to 14 AWG)

• Torque 0.5 to 0.6 Nm (0.37 to 0.44 ft-lbs)

15.7 Certificates and approvals

15�7�1 CE mark

The device meets the legal requirements of the applicable EC guidelines. These are listed

in the corresponding EC Declaration of Conformity together with the standards applied.

Hauser confirms successful testing of the device by affixing to it the CE mark.

15�7�2 Ex approval

The process transmitter with control unit FTR525, as an associated apparatus, is only

permissible exclusively for use outside of the hazardous area. The FTR525 controls the

devices FQR57/FDR57 of the Soliwave microwave barrier, which are installed inside of the

hazardous area. Please observe the safety notes of the separate "Safety Instructions" (XA),

reference is made to this document on the nameplate.

The separate Safety Instructions (XA) with all information regarding explosion

protection is available from the Hauser Sales Center or in the download area

of the internet site

www.endress.com

15�7�3 Other standards and guidelines

• EN 60529

Degree of protection provided by enclosures (IP code)

• EN 61010-1

Safety requirements for electrical equipment for measurement, control and laboratory

use

• EN/IEC 60079-0

Explosive atmospheres - Part 0: Equipment - General requirements

• EN/IEC 60079-11

Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"

• EN/IEC 60079-26

Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga

15�8 Supplementary documentation

• Technical Information Nivotester FTR525

TI01329F/97/EN

• Technical Information Soliwave FQR57/FDR57

TI01330F/97/EN

• Safety Instructions Nivotester FTR525 with Soliwave FQR57/FDR57

- ATEX: XA01603F/97/A3

- IECEx: XA01604F/97/EN

Summary of Contents for Nivotester FTR525





































































Search results

Summary of Contents for Nivotester FTR525

Reviews:

Related manuals for Nivotester FTR525

Brands by name

Popular brands

Endress+Hauser Nivotester FTR525, Operating Instructions Manual

Search results

Summary of Contents for Nivotester FTR525

Reviews:

Related manuals for Nivotester FTR525

Brands by name

Popular brands