Endress+Hauser Memosens CFS51 Operating Instructions Manual Download Page 41

Page: 41 / 44

Memosens CFS51

Technical data

Hauser

Degree of protection

• IP 68

• NEMA 6P

Electromagnetic

compatibility (EMC)

Interference emission and interference immunity according to:

• EN 61326-1:2013

• EN 61326-2-3:2013

• NAMUR NE21: 2012

13.4 Process

Process temperature range

–5 to 55 °C (20 to 130 °F)

Process pressure range

• Sensor: 0.5 to 10 bar (7.3 to 145 psi)

• Sensor with assembly: 0.5 to 6 bar (7.3 to 87 psi)

Flow limit

Minimum flow

No minimum flow required.

13.5 Mechanical construction

Dimensions

→ Section "Installation"

Weight

Sensor without clamping ring:

0.69 kg (1.52 lb)

Sensor with clamping ring:

0.78 kg (1.72 lb)

Materials

Sensor

Housing:

Titanium 3.7035

Optical window:

Sapphire

O-rings:

FKM, EPDM (seal of cable assembly)

Assembly

Flow cell:

PVDF V0, PA6FR (low flammability)

O-rings:

FKM

Clamping ring:

Titanium 3.7035

Process connections

• Sensor: G1" and NPT ¾"

• Assembly: G1/4" DN 4/6 (cleaning connection), G1/4" DN6/8 (process connection)

Summary of Contents for Memosens CFS51













































Search results

Summary of Contents for Memosens CFS51

Reviews:

Related manuals for Memosens CFS51

Brands by name

Popular brands

Endress+Hauser Memosens CFS51, Operating Instructions Manual

Search results

Summary of Contents for Memosens CFS51

Reviews:

Related manuals for Memosens CFS51

Brands by name

Popular brands