Endress+Hauser Hart Micropilot FMR60B Operating Instructions Manual Download Page 13

Page: 13 / 84

Micropilot FMR60B HART

Incoming acceptance and product identification

Hauser

4.2.2

Manufacturer address

Hauser SE+Co. KG

Hauptstraße 1

79689 Maulburg, Germany
Place of manufacture: See nameplate.

4.3

Storage and transport

4.3.1

Storage conditions

• Use the original packaging

• Store the device in clean and dry conditions and protect from damage caused by shocks

Storage temperature range

See Technical Information.

4.3.2

Transporting the product to the measuring point

WARNING

Incorrect transport!

The housing or sensor can be damaged or pull off. Risk of injury!

‣

Transport the device to the measuring point in its original packaging or by the process

connection.

‣

Always secure lifting equipment (slings, eyes, etc.) at the process connection and never

lift the device by the electronic housing or sensor. Pay attention to the center of gravity

of the device so that it does not tilt or slip unintentionally.

Summary of Contents for Hart Micropilot FMR60B





















































































Search results

Summary of Contents for Hart Micropilot FMR60B

Reviews:

Related manuals for Hart Micropilot FMR60B

Brands by name

Popular brands

Endress+Hauser Hart Micropilot FMR60B, Operating Instructions Manual

Search results

Summary of Contents for Hart Micropilot FMR60B

Reviews:

Related manuals for Hart Micropilot FMR60B

Brands by name

Popular brands