Endress+Hauser Hart Micropilot FMR60B Operating Instructions Manual Download Page 19

Page: 19 / 84

Micropilot FMR60B HART

Mounting

Hauser

0.7 Nm

A0038224

1. If fitted: release the screw of the cover lock for the electronics compartment cover

using the Allen key.

2. Unscrew the electronics compartment cover from the transmitter housing and check

the cover seal.

3. Press the release mechanism and remove the display module.
4. Turn the display module to the desired position: maximum 4 × 90 ° in each direction.

Fit the display module on the electronics compartment in the desired position until it

clicks into place. Screw the electronics compartment cover back onto the transmitter

housing. If fitted: tighten the screw of the cover lock using the Allen key

0.7 Nm (0.52 lbf ft)±0.2 Nm (0.15 lbf ft).

5.3.7

Changing the installation position of the display module

The installation position of the display can be changed in the case of the dual

compartment housing, L-form.

A0048401

Summary of Contents for Hart Micropilot FMR60B





















































































Search results

Summary of Contents for Hart Micropilot FMR60B

Reviews:

Related manuals for Hart Micropilot FMR60B

Brands by name

Popular brands

Endress+Hauser Hart Micropilot FMR60B, Operating Instructions Manual

Search results

Summary of Contents for Hart Micropilot FMR60B

Reviews:

Related manuals for Hart Micropilot FMR60B

Brands by name

Popular brands