Endress+Hauser Hart Micropilot FMR60B Operating Instructions Manual Download Page 55

Page: 55 / 84

Micropilot FMR60B HART

Accessories

Hauser

A0046692

Plastic single compartment housing, remote display

Aluminum single compartment housing, remote display

Device side, plastic single compartment housing prepared for remote display

Device side, aluminum single compartment housing prepared for remote display

Device side, dual compartment housing, L-form, prepared for remote display

Material of single compartment housing, remote display

• Aluminum

• Plastic

Degree of protection:

• IP68 / NEMA 6P

• IP66 / NEMA 4x

Connecting cable:

• Connecting cable (option) up to 30 m (98 ft)

• Standard cable provided by customer onsite up to 60 m (196 ft)

Ambient temperature:

• –40 to +80 °C (–40 to +176 °F)

• Option: –50 to +80 °C (–58 to +176 °F)

14.6 Gas-tight feedthrough

The chemically inert glass feedthrough which prevents gases from entering the electronics

housing is optionally available and can be ordered as a "Mounted accessory" via the product

structure.

14.7 Commubox FXA195 HART

For intrinsically safe HART communication with FieldCare via the USB interface

For details, see "Technical Information" TI00404F

14.8 HART Loop Converter HMX50

Is used to evaluate and convert dynamic HART process variables to analog current signals

or limit values.

Summary of Contents for Hart Micropilot FMR60B





















































































Search results

Summary of Contents for Hart Micropilot FMR60B

Reviews:

Related manuals for Hart Micropilot FMR60B

Brands by name

Popular brands

Endress+Hauser Hart Micropilot FMR60B, Operating Instructions Manual

Search results

Summary of Contents for Hart Micropilot FMR60B

Reviews:

Related manuals for Hart Micropilot FMR60B

Brands by name

Popular brands