Endress+Hauser Hart Micropilot FMR60B Operating Instructions Manual Download Page 12

Page: 12 / 84

Incoming acceptance and product identification

Micropilot FMR60B HART

Hauser

Incoming acceptance and product

identification

4.1

Incoming acceptance

DELIVERY NOTE

1 = 2

A0016870

Check the following during incoming acceptance:

• Is the order code on the delivery note (1) identical to the order code on the product

sticker (2)?

• Are the goods undamaged?

• Do the data on the nameplate correspond to the order specifications and the delivery

note?

• Is the documentation provided?

• If required (see nameplate): are the Safety Instructions (XA) provided?

If one of these conditions is not met, please contact the manufacturer's sales office.

4.2

Product identification

The following options are available for the identification of the measuring device:

• Nameplate specifications

• Extended order code with breakdown of the device features on the delivery note

‣

Device Viewer

(

www.endress.com/deviceviewer

); manually enter the serial number

from the nameplate.
 All the information about the measuring device is displayed.

‣

Hauser Operations app

; manually enter the serial number indicated on the

nameplate or scan the 2D matrix code on the nameplate.
 All the information about the measuring device is displayed.

4.2.1

Nameplate

The information that is required by law and is relevant to the device is shown on the

nameplate, e.g.:

• Manufacturer identification

• Order number, extended order code, serial number

• Technical data, degree of protection

• Firmware version, hardware version

• Approval-related information, reference to Safety Instructions (XA)

• DataMatrix code (information about the device)

Summary of Contents for Hart Micropilot FMR60B





















































































Search results

Summary of Contents for Hart Micropilot FMR60B

Reviews:

Related manuals for Hart Micropilot FMR60B

Brands by name

Popular brands

Endress+Hauser Hart Micropilot FMR60B, Operating Instructions Manual

Search results

Summary of Contents for Hart Micropilot FMR60B

Reviews:

Related manuals for Hart Micropilot FMR60B

Brands by name

Popular brands