background image

EN-KO Electronic Control Systems                                                                                                      

AMF 4.0/ENG/K.K./02

 

 

20

Enter  model  number  to  load  parameter  table  of  selected 
genset model. 

P70  Periodic service time 

This  parameters  selects  After  how  many  running  hour 
periodic service alarm will be given 

P71  Engine hour adjustment 

Engine hour is adjusted by this parameter. 

P72  Clear last ten alarm 

When you select “YES” and press menu key last ten failure 
is cleared. 

P73  Clear periodic service alarm 

When  you  select  “YES”  and  press  menu  key,  periodic 
service alarm is cleared and service time is reset 

P74  Return  to  technician  factory 

defaults 

When you select “YES” and press menu key technician 
parameters is returned to factory defaults 
 
 
 

 

Calibration Parameters 

 

P75  Calibration menu password 

Calibration menu password adjustment 

P76  Mains Vr gain  

Mains line R voltage gain calibration. 

P77  Mains Vs gain 

Mains line S voltage gain calibration. 

P78  Mains Vt gain 

Mains line T voltage gain calibration. 

P79  Generator Vr gain 

Generator line R voltage gain calibration. 

P80  Generator Vs gain 

Generator line S voltage gain calibration. 

P81  Generator Vt gain 

Generator line T voltage gain calibration. 

P82  Generator Ir gain 

Generator line R current gain calibration. 

P83  Generator Is gain 

Generator line S current gain calibration. 

P84  Generator It gain 

Generator line T current gain calibration. 

P85  Battery Voltage gain 

Battery voltage gain calibration. 

P86  Mains Vr offset 

Mains line R voltage offset calibration. 

P87  Mains Vs offset 

Mains line S voltage offset calibration. 

P88  Mains Vt offset 

Mains line T voltage offset calibration. 

P89  Generator Vr offset 

Generator line R voltage offset calibration. 

P90  Generator Vs offset 

Generator line S voltage offset calibration. 

P91  Generator Vt offset 

Generator line T voltage offset calibration. 

P92  Battery voltage offset 

Battery voltage offset calibration. 

P93  Oil pressure offset 

Oil pressure offset calibration. 

P94  Temperature offset 

Coolant temperature offset calibration. 

P95  Generator Ir offset 

Generator line R current offset calibration. 

P96  Generator Is offset 

Generator line S current offset calibration. 

P97  Generator It offset 

Generator line T current offset calibration. 

P98  Return  to  calibration  factory 

defaults 

When you select “YES” and press menu key calibration 
parameters is returned to factory defaults 

P99  Mains  contactor  control  in  off 

mode 

If  this  parameter  is  selected  as  “YES”,  Unit  will  control 
mains  voltages  in  off  mode  and  when  mains  exceed  the 
limits defined in parameter menu, mains contactor opens and 
protect the load and when mains returns to normal condition 
mains contactor closes. If this parameter is selected as “NO”, 
mains isn’t controlled and mains contactor is always closed. 

 

 
 

Summary of Contents for AMF 4.0























Reviews: