background image

EN-KO Electronic Control Systems                                                                                                      

AMF 4.0/ENG/K.K./02

 

 

18

started  in  auto  mode.  Mains  failure  delay  is  waited  before 
mains failure. 

P38  Generator under voltage failure  If  generator  voltage  fall  below  this  limit  under  over  voltage 

alarm occur. Failure occurred after  generator voltage failure 
delay 

P39  Generator over voltage failure 

If  generator  voltage  exceeds  this  limit  under  over  voltage 
alarm occur. Failure occurred after  generator voltage failure 
delay 

P40  Generator 

under 

frequency 

failure 

If generator frequency fall below this limit under over speed 
alarm  occur.  Failure  occurred  after  generator  frequency 
failure delay 

P41  Generator 

over 

frequency 

failure 

If  generator  frequency  exceeds  this  limit  under  over  speed 
alarm  occur.  Failure  occurred  after  generator  frequency 
failure delay 
 

P42  Last 10 failure 

Last ten alarm is recorded in the panel memory. There alarm 
can be controlled by this parameter. 

P43  Return to operator factory 

defaults 

When you select “YES” and press menu key operator 
parameters is returned to factory defaults 

 

Technician Parameters 

 

P44  Technician menu password 

Technician password can be changed by this parameter 

P45  Analog oil sender type 

Analog  oil  pressure  sender  type  can  be  selected  from  this 
parameter.  If  genset  has  only  digital  oil  switch,  and  this 
parameter is adjusted to “0” oil switch input is transferred to 
analog oil pressure sender input.  

P46  Oil switch type 

Oil pressure switch type can be selected from this parameter. 

P47  Low oil pressure failure 

If oil pressure fall below this limit. Oil pressure failure alarm 
is activated. 

P48  Analog 

temperature 

sender 

type 

Analog coolant temperature sender can be selected from this 
parameter.  If  genset  has  only  digital  coolant  temperature 
switch,  and  this  parameter  is  adjusted  to  “0”  coolant 
temperature switch input is transferred to analog temperature 
sender input. 

P49  Digital temperature switch type  Analog coolant temperature sender can be selected from this 

parameter. 

P50  Analog Oil pressure usage 

If analog sender is used for display purposes only. Generator 
doesn’t control this analog value. Value read from sender is 
used  only  for  display  purposes.  No  sensor  alarm  is  given  if 
sensor cable breaks. 

P51  Analog 

temperature 

sensor 

usage 

If analog sender is used for display purposes only. Generator 
doesn’t control this analog value. Value read from sender is 
used  only  for  display  purposes.  No  sensor  alarm  is  given  if 
sensor cable breaks. 

P52  Fueling system 

Fueling  system  is  can  be  adjusted  as  operating  or  stop 
solenoid.  When  this  parameter  is  selected  as  ECU  type. 
Cranking  output  behaves  like  start  output  and  fuel  solenoid 
output  behaves  like  stop  output.  This  configuration  is 
necessary in some type of ECU managed engines. In engine 
starting  condition,  start  output  is  activated  for  3  second  and 
cranking is stopped by means of activating stop output for 2 

Summary of Contents for AMF 4.0























Reviews: