background image

28188-2-0114

Page 12

CAUTION: ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE WITH ALL LOCAL, 

CITY AND STATE BUILDING CODES. BEFORE MAKING THE ELECTRICAL CONNECTION, MAKE SURE THAT MAIN POWER SUPPLY 

IS DISCONNECTED. THE APPLIANCE, WHEN INSTALLED, MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH LOCAL 

CODES OR, IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL ELECTRICAL CODE ANSI/NFPA 70 (LATEST EDITION)

A factory installed junction box is located on the lower right 

hand side of the firebox. Wiring must be fed to the junction box 

and attached to the receptacle that is provided. Remove the 

knockout in the installed junction box to accept wiring into the 

junction box. Install a UL listed cable clamp (not supplied) in the 

knockout hole. Leave approximately 6" of wire in the junction box 

for connection.
Attach black wire to one side of the receptacle and white wire to 

opposite side of receptacle. The ground wire should be attached 

to the green (neutral) screw.
Install the receptacle into the junction box. Attach cover plate.

Keep the control compartment, logs and burner area surrounding the 

logs clean by vacuuming or brushing area at least twice a year.
THE LOGS CAN GET VERY HOT – HANDLE ONLY WHEN 

COOL.
Always turn off gas to the pilot before cleaning. For relighting, refer 

to lighting instructions located on the log set.

Never obstruct the flow of the combustion and ventilation air. Keep 

the front of the firebox clear of all obstacles and materials.

Screens must be closed during operation.

Figure 20

JUNCTION BOX WIRING INSTALLATION INSTRUCTIONS

MAINTENANCE

PARTS LIST

INDEX NO.

PART NUMBER

DESCRIPTION

VFS32FB0F

VFS36FB0F

VFS42FB0F

1

17247

17247

17247

TOP STANDOFF

2

10554

10554

10554

FRAMING BRACKET

3

17162

17162

17162

JUNCTION BOX ASSEMBLY

4

R3492

R3492

R3492

RECEPTACLE

5

R3491

R3491

R3491

COVER, JUNCTION BOX

6

25101

25101

25101

BLOWER COVER

7

R8213

R8202

R8202

SCREEN CURTAIN

8

20020

20145

19984

HOOD

9

R7051

R7052

R7053

ROD, SCREEN

10

R9292

R9292

R9292

HEARTH LEDGE, RIGHT

11

R9293

R9293

R9293

HEARTH LEDGE, LEFT

12

R9294

R9295

R9296

HEARTH LEDGE, CENTER

13

23004

23004

23004

HEARTH RETAINER

Summary of Contents for VFS32FB0F-4

















Reviews: