background image

28188-2-0114

Page 4

Sidewall Clearances:

 The clearance from the inside of the firebox 

to perpendicular combustible side wall should not be less than 

6". Unit may be recessed as shown only with accessory liner kit 

installed. 

See Figure 1.

Firebox Side and Back Clearances:

 The firebox outer casing side 

and back flanges are zero clearance to combustibles.

Top Framing and Finishing:

 Combustible framing may rest on 

top  of  standoffs.  Combustible  finishing  materials  may  extend 

to the top standoff screws on the front edge of the outer wrap. 

See Figure 2

.

Ceiling Clearances:

 The ceiling height should not be less than 42" 

from the top of the hood. 

See Figures 3a and 3b.

Mantel Clearances: 

Vent free firebox models must use the hood 

supplied with the firebox, or one of the optional hood kits available 

for each model. If a combustible mantel is installed, it must meet 

the clearance requirements detailed below.

Grate Clearance: 

The minimum clearance between the front legs 

of the grate and front edge of the firebox is 2".

Leave at least 36" clearance from the front of the firebox.

CLEARANCES

45°

6"

3"

MAX.

PERPENDICULAR
SIDE WALL

FRONT FACE (SIDE)

FIREBOX

(TOP VIEW)

COMBUSTIBLE
MATERIALS ALLOWED
IN SHADED AREAS

WITH ACCESSORY LINER ONLY

MANTEL

STANDARD
HOOD

13”

10”

12”

MAX

42”

MIN.

(CEILING TO
TOP OF HOOD)

11 1/2”

MIN.

FIREBOX
FACE

84”

MIN.

(CEILING TO FLOOR)

CEILING

COMBUSTIBLES

ALLOWED

3/8” COMBUSTIBLE
CLEARANCE REQUIRED
FROM TOP EDGE
OF FIREBOX

10”

22”

8”

20”

6 ½”

18”

5”

16”

3 ½”

14”

2”

12 ½”

3/4”

24 ½”

0”

With Accessory Liner Only - Figure 1

Figure 2

Figure 3a - Mantel Clearances with Standard Hood

Figure 3b - Mantel Clearances with Optional Extended 

Hood

MANTEL

EXTENDED HOOD
(VB4H SERIES)

10”

12”

MAX

42”

MIN.

(CEILING TO
TOP OF HOOD)

8”

MIN.

FIREBOX
FACE

84”

MIN.

(CEILING TO FLOOR)

CEILING

COMBUSTIBLES

ALLOWED

3/8” COMBUSTIBLE
CLEARANCE REQUIRED
FROM TOP EDGE
OF FIREBOX

10”

22”

8”

20”

6 ½”

18”

5”

16”

3 ½”

14 ½”

2 ½”

24 ½”

0”

16 ½”

FIREBOX

STAND OFF

COMBUSTIBLE
FINISHED WALL
OR MANTEL

2 X 4
HEADER

TOP OUTER

WRAP

FINISH WITH TRIM KIT
OR NON-COMBUSTIBLE
MATERIAL AS DESIRED.

Summary of Contents for VFS32FB0F-4

















Reviews: