background image

The Heritage Cast Iron Stoves

INSTALLATION INSTRUCTIONS

AND 

OWNER'S MANUAL

This  appliance  may  be  installed  in  an  aftermarket 

permanently located, manufactured home (USA only) or 

mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas 

indicated  on  the  rating  plate.  This  appliance  is  not 

convertible for use with other gases, unless a certified 

kit is used.

WARNINg: Improper installation, adjustment, altera-

tion, service or maintenance can cause injury or prop-

erty damage. Refer to this manual. For assistance or 

additional  information  consult  a  qualified  installer, 

service agency, or the gas supplier.

CAST IRON

DIRECT VENT STOVE 

MODELS:

DVP30CA30(B,F,M,S,W)N-2

DVP30CA30(B,F,M,S,W)P-2

—  Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any 

other appliance.

—  WHAT TO DO IF YOU SMELL gAS

 

•  Do not try to light any appliance.

 

•  Do not touch any electrical switch; do not use 

any phone in your building.

 

•  Immediately  call  your  gas  supplier  from  a 

neighbor’s phone. Follow the gas supplier’s 

instructions.

 

•  If you cannot reach your gas supplier, call the 

fire department.

—  Installation and service must be performed by a 

qualified installer, service agency or the gas sup

-

plier.

WARNINg: If the information in these instructions 

are  not  followed  exactly,  a  fire  or  explosion  may 

result causing property damage, personal injury or 

loss of life.

Installer: 

Leave this manual with the appliance.

Consumer:  Retain this manual for future reference.

EMPIRE

EMPIRE

Comfort Systems

GAS-FIRED

Page 1

Summary of Contents for DVP30CA30BN-2









































Reviews: