Emerson Rosemount 5900 Reference Manual Download Page 43

Page: 43 / 100

Reference Manual

300520EN, Rev AA
November 2009

3-19

Rosemount 5900 Series

Section 3. Installation

5. Put the transmitter head onto the

antenna adapter.

6. Ensure that the guide pin inside the

transmitter head base fits the groove
on the adapter.

7. Tighten the nut that connects the

transmitter head to the adapter.

8. Ensure that the gauge is directed so

that the cross hairs on top of the
transmitter head points towards the
center of the tank.

9. Tighten the adapter screws



M10).

10. Put the Weather Protection Hood on

top of the transmitter head and
tighten the screw.

11. Connect the electrical cabling and

configure the gauge by using the
TankMaster WinSetup software (see
the

Raptor System Configuration

Manual

, Document No. 300510EN)

Transmitter head

Nut

Adapter

Tank

Tank center

Cross hairs

Weather

Protection Hood

Preliminary

Summary of Contents for Rosemount 5900





































































































Search results

Summary of Contents for Rosemount 5900

Reviews:

Related manuals for Rosemount 5900

Brands by name

Popular brands

Emerson Rosemount 5900, Reference Manual

Search results

Summary of Contents for Rosemount 5900

Reviews:

Related manuals for Rosemount 5900

Brands by name

Popular brands