background image

7

Type OSE

•  Precaution should be taken when removing or replacing 

the valve plug to avoid damaging the segments

•  Lubricate screws before tightening

•  Lubricate O-rings (silicone grease) except for the valve 

plug O-ring

•  Lightly lubricate the stem (silicone grease)

•  Lubricate the release relay mechanism (yoke and bolt) 

(molybdenum graphite grease)

•  Lubricate the BMS spring (molybdenum graphite grease)

A special tool is required when installing a new ori

fi

 ce

Table 7.

 Troubleshooting for Type OSE Slam-Shut Valve

Table 5.

 Torques for Connecting Part Screw 

(key 10, Fig. 7)

DN

Dimensions

Spanner (inches)

Torque

(N.m)

25

9/16-12 

X

 1 3/4

13/16’’

110

50

1/2-13 

X

 1 1/2

3/4’’

110

80

5/8-11 

X

 1 3/4

15/16’’

175

100

3/4-10 

X

 2 1/4

1’’1/8

260

150

1-8 

X

 2 3/4

1’’1/2

510

C58a

Table 6.

 Torques for Bypass (key 1. Fig. 7)

DN

Torque (N.m)

25

14

50

14

80

20

100

24

150

24

C58b

C58c

Key

Torque (N.m)

9

15

14

Table 4.

 Torques (key 9 & 14, Fig. 7)

SYMPTOMS

CAUSE

ACTIONS

If the valve will not close

Operating fault

Check the release relay

Check the valve plug
or contact after-sales

If the valve closes

Operating correctly

Observe the evolution of the outlet pressure

(check tightness)

If the outlet pressure in the slam shut is 

decreases

External leak

Locate and seal the leak

or contact after-sales

If the outlet pressure in the slam shut is 

constant

Bleed off the outlet side of the regulator

Observe the evolution of the outlet pressure

(check tightness)

If the outlet pressure increases

Internal leak

Check the slam shut valve plug

Check the ori

fi

 ce

Check the bypass

or contact after-sales

Key

Description

DN 25

DN 50

DN 80

DN 100

DN 150

1

Bypasse

180977

2

Valve plug O-ring

400257

400263

400258

400260

400261

3

Segments

401950

401951

401952

401953

401954

4

O-ring

400298

400295

400297

400296

19B0359X12

5

O-ring

400009

400024

400259

400045

400262

Packing gland “Kit” 

197395

Set of O-rings*

197447

197448

197449

197450

197451

Spare parts kit**

197452

197453

197454

197455

197456

Release Relay Type OS2

See D103683X012 manual

(*) Set of O-rings and segments including O-rings key 2, 3, 4, 5 

(**) Spare-parts kit including set of O-rings, bypass (key 1) and bypass disassembly spanner

Table 8.

 Spare Parts for Type OSE Slam-Shut Valve

SPARE PARTS

Summary of Contents for OSE Series









Reviews: