manualshive.com logo in svg

Emerson Liebert ITA 5kVA, User Manual

Share
Download
Emerson Liebert ITA 5kVA User Manual Download Page 50

42      Chapter 5  UPS Operation Instructions 

Liebert

®

 ITA 5kVA And 6kVA UPS    User Manual 

CB1

CB2

SW

 

Figure 5-53    Configuration of the single UPS with external maintenance bypass 

For the UPS system which requires the power distribution to be accomplished by user, if you need to isolate the UPS 
from AC power, disconnect the external input MCB. 

Warning 

Cut off the maintenance power to prevent physical injury.

 

 

5.9   Auto Restart 

Upon mains failure, the UPS supplies power to the load through battery until the battery power is depleted, and the 
UPS will terminate output. 
Meet the following conditions, the UPS will automatically restart and recover output power supply. 

 The mains restores after battery EOD; 

 The UPS EOD Auto Restart function is enabled. 

Note 

1. The UPS EOD Auto Restart function is enabled by default if there is no customized requirement. 
2. If the Auto Restart function is not enabled, you can start the UPS manually by pressing the ON/SILENCE key. 

 

5.10   UPS Monitoring 

For the methods of the UPS background monitoring, refer to 

SiteMonitor Monitoring Software User Manual

 delivered 

with the UPS. 
 

Summary of Contents for Liebert ITA 5kVA





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands