manualshive.com logo in svg

Emerson Fisher D3, Instruction Manual

Share
Download
Emerson Fisher D3 Instruction Manual Download Page 28

Instruction Manual

D103460X012

D3 Valve with easy-Drive Actuator

October 2017

28

A.2.5 Overspeed Condition

The drive speed was detected as being over the speed 3300RPM. This fault latches and needs to be reset.

A.2.6 Calibration Span Not in Legal Range

Following a calibration the detected mechanical travel was detected as being too short for the valve type. This fault
latches and needs to be reset.

A.2.7 Fault in NV Memory – recovered settings

This fault is similar to Fault in NV Memory but is different in that the settings were recovered, however it is possible the
fault was due to a setting being changed during a power cycle. The settings need to be validated before valve
operation.

A.2.8 Communications Timeout

This flag is set after a timeout or loss of valid communications, it will be cleared if communications is reestablished
with the valve controller. If this flag is set and the control demand is set to be taken from the Modbus then the valve
will be commanded to the ‘Loss of communications position’ in setting accessed at Modbus register 40034.

A.2.9 Valve was Shutdown while Moving

The valve was actuating while power was removed, the position information may be unreliable. Command valve to 0%
to assure position information is accurate.

A.2.10 Valve Span Calibrated

The valve is calibrated.

A.2.11 Valve Position Controller Active

The valve is being actively controlled to go to a demanded position. The speed and position control loop logic is
setting the pwm and direction demands to the ValuDrive motor.

A.2.12 Analog Input Below 3mA/0.75V

The analog input is below a set threshold of 3mA. If since being powered up this level has been met the flag ‘Analog
input initialized’ will be set. If the control source is the analog input and this flag is set then the valve will be
commanded to actuate to the ‘Loss of control input’ position.

A.2.13 Motor Overspeed Coast Condition

The drive speed was detected as being over the speed 2500RPM. The flag is cleared if the speed falls below the coast
threshold level. This flag is used purely as a diagnostic.

A.2.14 Modbus Command Initialized

The system has received a command to the Position demand register since being powered up. If Modbus is the
selected control mode the valve will be commanded to this position after the startup period.

Summary of Contents for Fisher D3





































Reviews:

No comments

Brands by name

Popular brands

Load more brands