Emerson Fisher D3 Instruction Manual Download Page 2

Page: 2 / 36

Instruction Manual

D103460X012

D3 Valve with easy-Drive Actuator

October 2017

Table 1. Specifications

Valve Body Sizes, End Connection Styles, and Port
Diameters

(1)

VALVE

SIZE,

NPS

PORT

DIAMETER,

(INCHES)

THREADED

RAISED FACE

(RF) FLANGED

CL900

CL600

0.375, 0.75, 1

X = Available construction.

Maximum Inlet Pressures and Temperatures

(1)

VALVE BODY SIZE

MAXIMUM INLET

PRESSURE

TEMPERATURE RANGE

bar (psig)

C (

NPS 1 NPT

CL900

155 (2250)

-46 to 93 (-50 to 200)

150 (2185)

93 to 149 (200 to 300)

NPS 2 NPT

CL900

155 (2250)

-46 to 93 (-50 to 200)

150 (2185)

93 to 149 (200 to 300)

NPS 1 RF

CL600

103 (1500)

-46 to 93 (-50 to 200)

100 (1455)

93 to 149 (200 to 300)

NPS 2 RF

CL600

103 (1500)

-46 to 93 (-50 to 200)

100 (1455)

93 to 149 (200 to 300)

Maximum Shutoff Pressure Drops

(1)

MAXIMUM

P BAR (PSI) PER PORT SIZE

Port Size,

mm (inch)

9.5 (0.375)

19.1 (0.75)

25.4 (1.00)

Flow Up

155 (2250)

105 (1518)

75 (1089)

Flow Down

155 (2250)

130 (1889)

Shutoff Classification per ANSI/FCI 70‐2
and IEC 60534‐4

Class IV

Flow Characteristic / Valve Plug Style

Equal percentage / Micro‐Form Valve Plug

Maximum Travel

15 mm (0.6 inch)

Material Temperature Capabilities

(1)

Valve Body Assembly:

Standard Bonnet O-Ring:

-40 to 135

C (-40 to 275

Electric Actuator Assembly:

-20 to 70

(-4 to 158

F), < 90% non-condensing humidity

Flow Direction

Flow up (standard), Flow down (optional)

Available Actuator Configurations

On/off (snap acting)
Positioning (flow or pressure control)

Power Requirements

12 or 24VDC, minimum 4 amp power supply required
(fuse to 5 amps)

Maximum Current Draw

4 amps

Idle Current Draw

38 mA

Conduit Connections

Two 3/4 NPT connections

Stroke Length

FloPro controlled between 10mm (0.4 inch) and
15mm (0.6 inch)

Nominal Stroke Speed

(2)

3.9 mm/s (0.15 inch/s) at 24 VDC
2.2 mm/s (0.09 inch/s) at 12 VDC

Hazardous Area Approvals

CSA (C/US):

ExplosionProof Class I, Division 1,

Groups C and D, T6, Ex d IIA T6, Class I, Zone 1, AEx d
IIA T6

ATEX Flameproof - Gas:

II 2 G ,Ex d IIA T6

IECEx Flameproof - Gas:

Ex d IIA T6

Enclosure Rating

Type 4X and IP66

Duty Cycle

50% maximum

Enclosure Material

Cast aluminum alloy with powder coat paint

Approximate Weight:

18 - 27 kg (39 - 60 lbs), depending upon construction

1. The pressure or temperature limits in the referenced tables and any applicable ASME code limitations should not be exceeded.

2. 10% variation can be expected, based on temperature and pressure of application.

Summary of Contents for Fisher D3





































Search results

Summary of Contents for Fisher D3

Reviews:

Brands by name

Popular brands

Emerson Fisher D3, Instruction Manual

Search results

Summary of Contents for Fisher D3

Reviews:

Brands by name

Popular brands