Emerson Daniel 762 User Manual Download Page 68 | Manualshive

Page: 68 / 116

background image

Lifting and installation conditions

(continued)

Table 4-1:

Conditions

Description

Soil/floor loadings and prod-
uct/piping support

Follow local procedures that meet the standards for soil/floor
loading and product/piping support.

4.2

Lifting requirements for personnel

4.2.1

Safety precautions using appropriately rated lifting

slings

WARNING!

LIFTING HAZARD

The lifting instructions are for installation and removal of a Daniel control valve only and do not
address lifting the control valve while it is attached or bolted to piping.

Failure to follow these instructions may result in death, serious injury or equipment damage.

•

Only personnel properly trained in the safe practices of rigging and lifting should lift
valves.

•

Prior to use, visually inspect the slings for any signs of abrasion or other damage.
Refer to the sling manufacturer for inspection procedures specific to the sling you
are using.

•

Never attempt to lift the valve by wrapping slings around the visual indicator,
position indicator pilots, needle valves, accessories or tubing.

•

Never attempt to lift the valve using only one sling around the valve. Always use two
slings wrapped around each end of the body as shown below. Use a choker style
sling with a spreader bar.

•

Only use slings with ratings that exceed the weight to be lifted. Reference all safety
standards for safety factors that must be included when calculating the load rating.

CAUTION!

SLING HAZARD

Never allow the slings to come in contact with the visual indicator, position indicator, pilots,
needle valves, accessories or tubing. Use a spreader bar on the sling to prevent contact.

Failure to comply may cause equipment damage.

•

Never apply shock loads to the valve. Always lift the control valve gradually. If shock
loading occurs, inspect the slings per manufacturer's procedures before reuse.

Prepare the control valve for use

58

Daniel Models 762, 763, 765, 766 and 767 Control Valves

«
...
66
67
68
69
70
...
»

Summary of Contents for Daniel 762





















































































































Reviews:

No comments

Related manuals for Daniel 762

Brand: Samson Pages: 36

Brand: FBII Pages: 71

Brand: CAME Pages: 4

Brand: Samson Pages: 20

Brand: C.Nord Pages: 100

CoreBuilder 9000

Brand: 3Com Pages: 78

Brand: Banner Pages: 15

Brand: bar Pages: 2

Elemec3 013-02-0095-002

Brand: GAI-Tronics Pages: 12

Brand: Parker Pages: 44

Brand: Zennio Pages: 30

Brand: Zeta Pages: 13

Brand: Belimo Pages: 9

Apollo 70-600 Series

Brand: Conbraco Industries Pages: 4

Brand: Ravel Pages: 33

Brand: Vaniman Pages: 2

MISTCATCH OMC-ATW-N2-AW

Brand: OHM ELECTRIC Pages: 8

Brand: DMP Electronics Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands