Emerson Daniel 762 User Manual Download Page 53

Page: 53 / 116

Operating conditions and

specifications

Topics covered in this chapter:

•

Operating conditions for the control valve

•

Specifications for the control valve

2.1

Operating conditions for the control valve

Table 2-1:

Condition type

Description

Fluid phase

Liquid

Process temperature

-26°C to 205°C (-15°F to 400°F)

Optional process tempera-
ture

-46°C to 205°C (-51°F to 400°F)

Fluid velocity

Operational recommended flow velocity up to 58 ft/sec, beyond this
point will result in a high pressure drop and increased wear.

Fluid(s) controlled

•

Low/Medium viscosity crude oils and condensates

•

Refined products and intermediates (ie:

gasoline, diesel, kerosene,

light fuel oils, jet fuel, LPG, butanes, naphtha, alkylate, reformate,
straight run gasoline, cat-cracked gasoline

)

•

Petrochemicals (ie:

benzene, toluene, xylenes, cumene, olefins, py-

rolysis gasoline

)

•

Natural gas liquids

Viscosity limits on valves

•

Maximum valve viscosity is 8800 Cst

•

Maximum viscosity for valves with pilots is 440 Cst due to re-
sponse time of high viscosity pilot

Differential pressure

The maximum allowable differential pressure across a control valve is
6894 kPa (1,000 psi). Consult factory for location of first shut down
valve.

Atmospheric pressure

Absolute

Sizes (NPS)

2, 3, 4, 6, 8,10,12,16

Pressure class (ANSI)

150, 300, 600

Maximum safe working
temperature range

•

-26°C to 205°C (-15°F to 400°F)

•

Using FKM O-rings

•

Temperature range is dependent of O-ring T

min

and T

max

•

Consult the factory for other safe working temperatures

Operating conditions and specifications

User manual

Summary of Contents for Daniel 762





















































































































Search results

Summary of Contents for Daniel 762

Reviews:

Related manuals for Daniel 762

Brands by name

Popular brands

Emerson Daniel 762, User Manual

Search results

Summary of Contents for Daniel 762

Reviews:

Related manuals for Daniel 762

Brands by name

Popular brands