Emerson Daniel 762 User Manual Download Page 83

Page: 83 / 116

Installation procedure

Topics covered in this chapter:

•

External components assembly

•

Oil filling procedure for valve with drain port

6.1

External components assembly

Install the external components (e.g., flanges) onto the pipeline.

The control valve is assembled at the factory. The components do not need to be
uninstalled or reinstalled unless maintenance is required.

CAUTION!

SURFACE TEMPERATURE HAZARD

The control valve body and piping may be extremely hot or cold.

Wear personal protective equipment appropriate to the situation when working with the
control valve. Adhere to your company's safety standards and practices.

Failure to comply may cause serious injury.

6.1.1

Fasteners

The property class of the fastener is in accordance with ASME B16.5.

Stud bolt and nut types

All fasteners (nuts and studs) used in assembling Daniel control valves are made of one of
the materials listed in the table below.

Bolt material selection

Table 6-1:

Bolt material selection

Description

ASTM SA 193 Grade B7 <63.5 mm (<2.5 in.)

High strength low alloy steel

ASTM SA 193 Grade B7M <63.5 mm (<2.5 in.)

Controlled strength low alloy steel

ASTM SA 320 Grade L7 <63.5 mm (<2.5 in.)

High strength low alloy low temperature steel

ASTM SA 320 Grade L7M <63.5 mm (<2.5 in.)

Controlled hardness low temperature steel

ASTM SA 449 <25.4 mm (<1.0 in.)

Quenched and tempered steel

ASTM SA 453 Grade 660

High temperature stainless steel

Installation procedure

User manual

Summary of Contents for Daniel 762





















































































































Search results

Summary of Contents for Daniel 762

Reviews:

Related manuals for Daniel 762

Brands by name

Popular brands

Emerson Daniel 762, User Manual

Search results

Summary of Contents for Daniel 762

Reviews:

Related manuals for Daniel 762

Brands by name

Popular brands