background image

Type 99

5

The monitoring pilot should be upstream of the working 

monitor regulator.  This enables a closer setpoint 

between the working regulator and the monitoring 

pilot.  Special Types 161AYW and 627-109 monitoring 

pilots with quick-bleed operation have been designed 

to give faster response to abnormal downstream 

conditions.  Table 4 gives the spread between normal 

distribution pressure and the minimum pressure at 

which the working monitor regulator can be set to take 

over if the working regulator fails open.

Wide-Open Monitor

The control line of the upstream regulator is 

connected downstream of the second regulator 

(Figure 5), so that during normal operation the 

monitoring regulator is standing wide open with the 

reduction to distribution pressure being taken across 

the working regulator.  Only in case of open failure of 

the working regulator does the wide-open monitoring 

regulator take control at its slightly higher setting.

The upstream regulator must have an O-ring seal on 

the valve carrier assembly.  This seals off the leak 

path that otherwise would let line pressure ahead of 

the working regulator inlet try to close the wide-open 

monitoring regulator.

Figure 4.

  Working Monitor Installation

Figure 5.

  Typical Wide-Open Monitor Installations

FLEXIBLE aRRangEMEnT THaT PERMITS WIDE-OPEn 

MOnITOR TO BE EITHER UPSTREaM OR DOWnSTREaM

FLEXIBLE aRRangEMEnT THaT PERMITS WIDE-OPEn 

MOnITOR TO BE EITHER UPSTREaM OR DOWnSTREaM

10A1388-A

A2504

UPSTREaM 

REgULaTOR 

(REqUIRES O-RIng 

STEM SEaL)

OPTIOnaL PILOT 

SUPPLy REgULaTOR

10A1386-A

A2503

UPSTREaM 

REgULaTOR 

(REqUIRES O-RIng 

STEM SEaL)

WORKIng 

REgULaTOR

OPTIOnaL PILOT 

SUPPLy REgULaTOR

20A1389-A

B2484

DISTRIBUTIOn PRESSURE 

COnTROL LInE

TyPE 161ayW MOnITORIng 

PILOT (aLSO REPRESEnTaTIvE 

OF TyPE 627-109)

PILOT SUPPLy LInE

WORKIng 

MOnITOR PILOT

InTERMEDIaTE 

PRESSURE

InTERMEDIaTE PRESSURE 

COnTROL LInE

LOaDIng 

PRESSURE

UPSTREaM 

PRESSURE

OPTIOnaL 

PILOT SUPPLy 

REgULaTOR

WORKIng 

MOnITOR 

REgULaTOR

WORKIng 

REgULaTOR

OPTIOnaL 

PILOT SUPPLy 

REgULaTOR

PILOT SUPPLy PIPIng FOR WORKIng REgULaTOR 

WHEn PILOT IS REqUIRED TO BE SUPPLIED FROM 

UPSTREaM PRESSURE

DISTRIBUTIOn 

PRESSURE 

Summary of Contents for 99





















Reviews: