background image

Type 99

12

Parts Ordering

A serial number is assigned to each regulator, and it 

is stamped on both the actuator and pilot nameplates.  

If the pilot is replaced, the new pilot will have its own 

serial number different from the main valve serial 

number.  Always indicate one or both serial numbers 

when communicating with your local Sales Office.  

When ordering a replacement part, be sure to include 

the complete eleven-character part number.

Parts List

Key  Description 

Part number

 

Repair kits include parts for regulator with composition

 

trim only, key numbers 7, 11, 16, 19, 20, and 57.  Also 

 

included are parts for pilot, key numbers 30, 33, 38, 40, 

 

48, 49, 50, 52, 71, 117, 126, 129, 150, 153, and 

 

P590 Series filter, key numbers 2 and 7.

 

  With low pressure pilot

 

    7/8-inch (22,2 mm) orifice  

R99LX000012

 

    1-1/8-inch (28,6 mm) orifice  

R99LX000022

 

  With high pressure pilot

 

    7/8-inch (22,2 mm) orifice  

R99HX000012

 

    1-1/8-inch (28,6 mm) orifice  

R99HX000022

 

  With extra high pressure pilot

 

    7/8-inch (22,2 mm) orifice  

R99HPX00012

 

    1-1/8-inch (28,6 mm) orifice  

R99HPX00022

Travel Indicator assembly (Figure 6)

Key  Description 

Part number

 

Complete Assembly (includes individual parts

 

  listed below)  

20A7146X0C2

  1  

Spring Case, Cast iron  

2L296219012

  101   Indicator Stem Adaptor, Aluminum  

1R395909012

  102   Indicator Cap, Aluminum  

1L290809012

  103   Indicator Stem, Aluminum  

1L296509022

  104   Disk Nut, Plastic  

1F730506992

  105   Machine Screw Nut, Plated steel (2 required)  

1A342024152

  106   Retainer, Aluminum  

1L291009012

  107   Indicator Window, Glass  

1L296706992

  108*  Gasket, Neoprene (CR) (2 required)  

1L291103012

  109*  Indicator Cover, Plastic (2 required)  

1L296405032

  110   Machine Screw, Plated steel (8 required)  

1A899028982

  111*  O-ring, Nitrile (NBR) (2 required)  

1E591406992

  112   Indicator Scale, Stainless steel 

1J511638982

actuator and Main Body assembly 

(Figures 6, 7, 8, 9, 10, and 11)

Key  Description 

Part number

  1  

Standard Spring Case without travel

 

  indicator, Cast iron  

1B883119012

  2  

Main Spring Seat, Plated steel

 

  250 psid (17,2 bar d) maximum 

 

    allowable pressure drop, Cast iron  

1B883219042

 

  1000 psid (69,0 bar d) maximum allowable 

 

    pressure drop  

1E242724092

*Recommended Spare Parts

Figure 6. 

Travel Indicator Assembly

 20A7146-B

Summary of Contents for 99





















Reviews: