EMBRON Hatteland HD 12T21 MMC Series, User Manual

Page: 113 / 124

Pinout Assignments
113
IND100241-19
Appendix
9-pin Amplifi ed Mono/Stereo Audio Out, DSUB Female
Type Number “HT 00235 OPT-A1”
5 4 3 2 1
9 8 7 6
PIN 01 LAUDR Left Audio Return*
PIN 02 LAUD Left Audio*
PIN 03 RAUDR Right Audio Return
PIN 04 RAUD Right Audio
PIN 05 N/C No internal connection
PIN 06 N/C No internal connection
PIN 07 N/C No internal connection
PIN 08 N/C No internal connection
PIN 09 N/C No internal connection
*For Mono: connect pin 01 and 02 only
COM Module RS-232 - 4 x ports, 9-pin DSUB Male
Type Number “PCA100294-1”
B
A
D
C
1 2 3 4 5
6 7 8 9
PIN 01 DCD Data Carrier Detect
PIN 02 RxD Receive Data
PIN 03 TxD Transmit Data
PIN 04 DTR Data Terminal Ready
PIN 05 GND Signal Ground
PIN 06 DSR Data Set Ready
PIN 07 RTS Request To Send
PIN 08 CTS Clear To Send
PIN 09 RI Ring Indicator
10+10 pin Isolated Digital Input/Output Module
Type Number “PCA100297-1”
Module A Module B
Module A Module B
A1 External Power + A1 IN+[0]
A2 N/C (Not Connected) A2 IN-[0]
B1 External Power - (GND1) B1 IN+[1]
B2 N/C (Not Connected) B2 IN-[1]
O1 HS[0] O1 N/C
C1 HS[1] C1 IN+[2]
C2 N/C (Not Connected) C2 IN-[2]
D1 HS[2] D1 IN+[3]
D2 N/C (Not Connected) D2 IN-[3]
O2 HS[3] O2 N/C
4+4 pin CAN I/O Module, 2 channels
Type Number “ZIA0001310-B / ZIA0001310-SLCAN”
X8
CAN1
X9
CAN2
1 2 3 4
1 2 3 4
Pin 01 X8 - Can1: 081 In Low
Pin 02 X8 - Can1: 082 Out Low
Pin 03 X8 - Can1: 083 In High
Pin 04 X8 - Can1: 084 Out High
Pin 01 X9 - Can2: 091 In Low
Pin 02 X9 - Can2: 092 Out Low
Pin 03 X9 - Can2: 093 In High
Pin 04 X9 - Can2: 094 Out High
10+10 pin RS-422 / RS-485 NMEA Module
Type Number “PCA200828-1 / PCA100293-1”
6 7 8 9 10
1 2 3 4 5
6 7 8 9 10
1 2 3 4 5
PIN 01 TxD- Transmit Data Negative
PIN 02 TxD+ Transmit Data Positive
PIN 03 GND Isolated Ground
PIN 04 RxD- Receive Data Negative
PIN 05 RxD+ Receive Data Positive
PIN 06 TxD- Transmit Data Negative
PIN 07 TxD+ Transmit Data Positive
PIN 08 GND Isolated Ground
PIN 09 RxD- Receive Data Negative
PIN 10 RxD+ Receive Data Positive
RS-485 Half Duplex (2-wire) Confi guration:
Connect TX and RX pair-wise:
TX- to RX-, TX+ to RX+.
*Note: The jumper for “force of transmitter
(Forced TX(y)” is open by factory default. For
some custom models this jumper is preset
to closed (active), in that case unit has to be
opened and jumper set to open to allow Half
Duplex mode.