elsner elektronik Mini-Sewi KNX L-Pr Installation And Adjustment Manual Download Page 42

Page: 42 / 68

Parameter setting

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

Specify when the current

control variables

of the controller are to be

sent

to the bus.

Periodic sending is safer, in case a message does not reach a recipient. You may also
set up periodical monitoring by the actuator with this setting.

The

status object

reports the current status of the control variables (0% = OFF,

>0% = ON) and may for example be used for visualisation, or to switch off the
heating pump as soon as the heating is switched off.

Then define the

type of control

. Heating and/or cooling may be controlled in two le-

vels.

General setpoint values

You may enter separate setpoint values for each mode or use the comfort setpoint as
a basic value.

Behaviour of the blocking object with value

• 1 = Block | 0 = release
• 0 = block | 1 = release

Value of the blocking object after reset

0 • 1

Send control variable

• on change
• on change and periodically

from change (in % absolute)

1...10; 2

Cycle

(if sent periodically)

5 s • ... • 5 min • … • 2 h

Send status objects

• on change
• on change to 1
• on change to 0
• on change and periodically
• on change to 1 and periodically
• on change to 0 and periodically

Cycle

(if sent periodically)

5 s • ... • 5 min • … • 2 h

Type of control

• Single level heating
• Dual-level heating
• Single-level cooling
• Dual-level cooling
• Single-level h single-level cooling
• Dual-level h single-level cooling
• Dual-level h dual-level cooling

Summary of Contents for Mini-Sewi KNX L-Pr





































































Search results

Summary of Contents for Mini-Sewi KNX L-Pr

Reviews:

Related manuals for Mini-Sewi KNX L-Pr

Brands by name

Popular brands

elsner elektronik Mini-Sewi KNX L-Pr, Installation And Adjustment Manual

Search results

Summary of Contents for Mini-Sewi KNX L-Pr

Reviews:

Related manuals for Mini-Sewi KNX L-Pr

Brands by name

Popular brands