elsner elektronik Mini-Sewi KNX L-Pr Installation And Adjustment Manual Download Page 53

Page: 53 / 68

Parameter setting

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

Block

The switching output can be blocked using an object.

If the block is activated, define specifications here for the behaviour of the output when
blocked.

The behaviour of the switching output on release is dependent on the value of the pa-
rameter "Switching output sends" (see "Switching output")

Switching delay from 1 to 0

(If delay can be set via objects:
valid until 1st communication)

None • 1 s • 2 s • 5 s • 10 s • … • 2 h

Switching output sends

• on change
• on change to 1
• on change to 0
• on change and periodically
• on change to 1 and periodically
• on change to 0 and periodically

Cycle

(is only sent if periodically is selected)

5 s • 10 s • 30 s… • 2 h

Use switching output block

No • Yes

Analysis of the blocking object

• At value 1: block | At value 0: release
• At value 0: block | At value 1: release

Blocking object value before first communi-
cation

0 • 1

Behaviour of the switching output

On block

• Do not send message
• send 0
• send 1

On release
(with 2 seconds release delay)

[Dependent on the "Switching output
sends" setting]

Switching output sends on change

• Do not send message
• Send switching output status

Switching output sends on change to 1

• Do not send message
• if switching output = 1



send 1

Switching output sends on change to 0

• Do not send message
• if switching output = 0



send 0

Switching output sends on change and
periodically

Send switching output status

Switching output sends on change to 1
and periodically

if switching output = 1



send 1

Switching output sends on change to 0
and periodically

if switching output = 0



send 0

Summary of Contents for Mini-Sewi KNX L-Pr





































































Search results

Summary of Contents for Mini-Sewi KNX L-Pr

Reviews:

Related manuals for Mini-Sewi KNX L-Pr

Brands by name

Popular brands

elsner elektronik Mini-Sewi KNX L-Pr, Installation And Adjustment Manual

Search results

Summary of Contents for Mini-Sewi KNX L-Pr

Reviews:

Related manuals for Mini-Sewi KNX L-Pr

Brands by name

Popular brands