elsner elektronik Mini-Sewi KNX L-Pr Installation And Adjustment Manual Download Page 41 | Manualshive

Page: 41 / 68

background image

39

Parameter setting

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

gramming" should not be used for the initial start-up, as the factory settings are always
used until the 1st communication (setting via objects is ignored).

For an adequate regulation of the ambient temperature, comfort, standby, eco and
building protection modes may be used.

Comfort

when present,

Standby

during short absences,

Eco

as a night-time mode and

Frost/heat protection

(building protection) e. g. with the window open.

The settings for the temperature control include the setpoint temperatures for the in-
dividual modes. Objects are used to determine which mode is to be selected. A change
of mode may be triggered manually or automatically (e.g. by a timer, window contact).

The

mode

may be switched with two 8 bit objects of different priority. Objects

„... HVAC mode (Prio 2)“ for switching in everyday operation and
„... HVAC mode (Prio 1)“ for central switching with higher priority.
The objects are coded as follows:
0 = Auto
1 = Comfort
2 = Standby
3 = Eco
4 = Building Protection

Alternatively, you can use three objects, with one object switching between eco and
standby mode and the two others activating comfort mode and frost/heat protection
mode respectively. The comfort object blocks the eco/standby object, and the frost/
heat protection object has the highest priority. Objects
„... Mode (1: Eco, 0: Standby)“,
„... comfort activation mode" and
„... frost/heat protection activation mode"

Select the

mode to be activated after reset

(e.g. power failure, reset of the line via

the bus) (Default).
Then configure a temperature control

block

via the blocking object.

Maintain the

Target values and extension time received
via communication objects

• never
• after power supply restoration
• after power supply restoration and
programming

Switch mode via

• two 8 Bit objects (HVAC Modes)
• three 1 bit objects

Mode after reset

• Comfort
• Standby
• Eco
• Building protection

«
...
39
40
41
42
43
...
»

Summary of Contents for Mini-Sewi KNX L-Pr





































































Reviews:

No comments

Related manuals for Mini-Sewi KNX L-Pr

Brand: Data Harvest Pages: 19

Brand: Paradox Pages: 72

Brand: Panamalar Pages: 32

Brand: Axis Pages: 2

Brand: Axis Pages: 2

Brand: Eneo Pages: 52

Brand: Response Pages: 38

Brand: System Sensor Pages: 2

Brand: GST Pages: 11

Brand: Linear Pages: 39

Brand: DAITEM Pages: 19

VIP-CAM-30-20 Series

Brand: PureLink Pages: 20

Brand: Ganz Pages: 4

Brand: M-system Pages: 3

Brand: i-PRO Pages: 44

Brand: DSC Pages: 8

Brand: Abus Pages: 61

Brand: echoflex Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands