manualshive.com logo in svg

elsner elektronik KNX eTR 101-BA2, Installation And Adjustment

Share
Download
elsner elektronik KNX eTR 101-BA2 Installation And Adjustment Download Page 5

3

Safety and operating instructions

Room Temperature Controller KNX eTR 101-BA2

 • Version: 20.04.2021 • Technical changes and errors excepted.

1.

Safety and operating instructions

1.1. Installation notes

Installation, testing, operational start-up and troubleshooting should 
only be performed by an authorised electrician.

CAUTION!
Live voltage! 

There are unprotected live components inside the device.

•

Comply with the locally applicable directives, regulations and provisions 

for electrical installation. 
•

De-energise all cables to be mounted and take safety precautions 

against unintentional switch-on.
•

Inspect the device for damage before installation. Only put undamaged 

devices into operation. 
•

Immediately take the device or system out of service and secure it 

against unintentional switch-on if risk-free operation is no longer guaranteed.

Use the device exclusively for building automation and observe the operating
instructions. Improper use, modifications to the device or failure to observe the
operating instructions will invalidate any warranty or guarantee claims.
Operate the device only as a fixed-site installation, i.e. only in assembled condition and
after conclusion of all installation and operational start-up tasks, and only in the
surroundings designated for it.
Elsner Elektronik is not liable for any changes in norms and standards which may occur
after publication of these operating instructions.

For information on installation, maintenance, disposal, scope of 
delivery and technical data, please refer to the installation 
instructions.

2.

Description

The 

Room Temperature Controller KNX eTR 101-BA2

 measures the room

temperature and displays the current value in white illuminated figures. Via the bus the
device can receive an external measured value and process it with own data to overall
temperature value (mixed value).

The 

KNX eTR 101-BA2

 has got an integrated PI controller for a heating and a cooling

system (one or two step). The room temperature is adjusted by means of the + and -
touch buttons.

Either binary contacts such as push-buttons or window contacts or analogue
temperature sensors T-NTC can be connected to 2 inputs.

Summary of Contents for KNX eTR 101-BA2



































Reviews:

No comments

Brands by name

Popular brands

Load more brands