background image

© 27.04.2005 ELKA-Torantriebe GmbH u. Co. Betriebs KG                     Page 7  

                                   EST 4004K 

 

 

7.1. Connections 

 

PE 

 Ground 

 Power 

supply 

L1 

 

Phase L1 

Power supply. 230 V 50Hz. The LED Vp lights if net voltage is present. 

 Neutral 

 Power 

supply 

 

------- 

(N)  

Neutral 

APL-RT 

Red signal, 230 V max. 60 W. The red light is on when the gate is closed and warning prior 
opening is not active. 

APL-GN 

Green signal, 230 V max. 60 W. The green light is on when the gate is open and warning 
prior closing is not active. 

(N)  

Neutral 

WARN 

Warning light 230 V max. 60 W. The warning light is on every time the gate moves and also 
if a warning prior to moving is active. 
The warning light can be used also as red if it’s desired that red turns off when the gate is 
closed. 

 

Gate status 

Warning 

Red 

Green

 

Gate closed 

Off 

On 

Off 

Gate 

open 

Off Off On 

Prior warning and movement 

On 

Off 

Off 

Gate stopped in any position in between 

Off 

Off 

Off 

Gate stopped at pedestrian position 

Off 

Off 

Off 

------- 

(N)  

 

Neutral for motor (Common for both directions) 

AUF 

 

Motor open - Direction 

ZU 

 

Motor close - Direction 

 

EXT-AUF

  

Transmission of the signal BA1 to a second control box (n.o.). 
The relay EXT-AUF (max. 24V, 100mA) energises if BA1 is pressed, or the corresponding 
remote button is used and falls off after about 1 second. The connection EXT-AUF can be 
used to transmit the signal to a open-input to a second control box e.g. for a barrier. 

------- 

BA1 

Button to open the gate (n.o.), the signal is transmitted to terminal EXT-AUF. The LED BA 
lights if BA1 or the corresponding remote button is pressed. A permanent open signal is 
possible. 

 

BA2 

Button to open the gate (n.o.), the signal is valid only for this controller. The LED BA lights 
when BA2 is pressed. A permanent open signal is possible. 

 

BZ 

Button to close the gate (n.o.). The LED BZ lights when pressed. Delayed closing is possible 
(see operating mode). 

 

LS 

Photo-cell (n.c.), or a jumper. The LED LS lights when the photo-cell is interrupted. The 
controller can react in three different ways (see section 7.2.). The photo-cell can also be 
connected to BS and used as a stop button. 

 

NB 

Toggle between day and night operating mode, works only when the optional timer card is 
being used (see section 8.). 

 

SLZ 

Safety contact strips (n.c.) for direction “gate closed”, or a resistor (8,2k

). The LED SLZ 

lights whenever the strips are activated. SLZ causes STOP and reversal for a short way. 

 
SLA 

Safety contact strips (n.c.) for direction “gate open”, or a resistor (8,2k

). The LED SLA 

lights whenever the strips are activated. SLA causes STOP and reversal for a short way. 

 

SEA 

 

Limit switch „gate open“ (n.c.) . The LED SEA turns off when limit switch is pressed. 

 

SEZ 

 

Limit switch „gate closed“ (n.c.). The LED SEZ turns off when limit switch is pressed. 

 

BS 

STOP button (n.c.) or a jumper. The LED BS turns off when BS is pressed. BS stops gate 
movement (electronic brake). The gate can only move again when BS is released and a new 
signal is given. 

 

BT 

Push button for serial switching OPEN-STOP-CLOSE-STOP (n.o.). The LED BT lights when 
BT or the corresponding remote button is pressed (see automatic closure, too). 

 

Summary of Contents for EST 4004K















Reviews: