Elk Products ELK-M1G Installation And Programming Manual Download Page 6

Page: 6 / 72

M1G Installation and Programming

Page 6

+SAUX

NEG

+VAUX

NEG

+VAUX

NEG

+VAUX

NEG

NORMAL

ZONE 16

JP1

SW1

16.5 V

JUMPER TO START
WITH NO AC

POWER

TELCO SEIZED

NEG

Z10
Z11

NEG

Z13

NEG

Z15

Z14

Z12

NEG

Z16

Z2
Z3

NEG

Aux12VDC Power Outputs

protected by 1.25A PTC NOTE:

Refer to Appendix F for the UL limitations on total continuous 'standby'
current drain from terSAUX, +VAUX, +VKP, and J16.

Replace Battery every 3-5 years.

Use ELK model #

ELK1280

(12V - 8 Ah) or

ELK12180

(12V - 18 Ah) or equivalent.

DIALER ACTIVE

SMOKE

2WIRE

STATUS

REVERSE
BAT LEADS

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

12 Volt
Sealed

Lead Acid

Control needs AC power to start. Momentarily shorting these two pads allows control to startup on battery only.

16.5VAC, 45VA UL Listed Class 2 Transformer -

ELK-TRG1640

DO NOT CONNECT TO A SWITCHED OUTLET

For Canada use cUL Listed Transformer -

ATC Frost # FPS-4016

18AWG Min.

NEG

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

N.C.

N.O.

ZONE

2200
Ohm

EOL

Master Power Switch (SW1)

, disconnects AC and Battery power from control.

This unit provides Residential fire alarm service when installed according to ANSI/NFPA 72. Transmission

of the fire alarm signal to a fire alarm headquarters or central station shall be permitted only with the

approval of the authority having jurisdiction. The burglar alarm signal shall not be transmitted to a police

emergency number, equipment is to be installed in accordance with NFPA (985,55.1.P).

Recommended locations and wiring methods shall be in accordance with CSA C22.1, Canadian Electrical

Code, Part I, Safety Standard for Electrical Installations; CAN/ULC-S302, Installation and Classification of

Burglar Alarm Systems for Financial and Commercial Premises, Safes and Vaults; and CAN/ULC-S301,

Standard for Central and Monitoring Station Burglar Alarm Systems.

Reference NFPA70 (NEC) & Canadian Electrical Code.

All circuits are current limited except for Battery leads. Refer to Appendix F.

For Installation of Residential Fire Warning Systems reference CAN/ULC-S540 Standard.

Testing of this system should be performed regularly with the primary AC power de-energized. Control

panel specifications are subject to change without notice.

Lithium 3V "Clock" battery, Varta #CR2032 located in upper left corner behind cover. Battery has a life

expectancy of approx. 10 years. Replace ONLY with exact model available at most electronics and camera

retailers.

"CAUTION: Lithium Battery May Explode If Mistreated. Do Not Recharge, Disassemble, or

Dispose Of In Fire."

Dialer/Modem is idle. If ON, Dialer/Modem is in use (communicating).

1 blink with equal On and Off times is Normal. 2 fast blinks = Control running on
bootloader only. 4 fast blinks = Control is re-initializing it's EEPROM memory after
a firmware flash. 5 fast blinks = Memory/Operation overflow

Battery is connected correctly. If ON, check battery lead connections.

AC Voltage is present and power switch is turned ON. If OFF, check AC power.

Phone line is good and house phones are connected. If ON constantly, the phone
line may be bad. During remote mode this LED will be ON since the house phones
are then disconnected from the outside line & are being powered from control.

TELCO

SEIZED

DIALER
ACTIVE

OFF

LEDS

Indicators

Power

Regular 1
sec. Blink

Battery

Reversed

OFF

Status

4-Wire Smoke Detector

2200

Ohm

EOL

To Zone Input

U.L. Listed EOL Supervision Relay

(

ESL #204

or Equivalent).

N.O. Alarm

Contacts

Sw12 VDC Output

protected by 1.1A PTC.

BATTERY

To Zone NEG

(Left Side Terminals)

Normal

State

Descriptions

Color Code for 2200

Ohm EOL Resistor

Part # ELK-ER2200

Color Code for 820

Ohm EOL Resistor

Part # ELK-ER820

NOTE: M1ZTS Temperature Sensors may only be connected to the first 16 zones.

Smoke Detector covers should be kept free
from dust and dirt by use of a dry or damp
(water) cloth as needed. When necessary,
clean the detector interior and/or replace the
optical chamber according to instructions
provided by the Smoke Detector Manufacturer.

2-Wire Smoke Detector

820

Ohm

EOL

NEG

Z16

Compatibility Identifier: M10001
Maximum Operating Voltage: 13.8 VDC
Max. wire resistance should not exceed 13 Ohms.
Use 18AWG Fire approved wire. Max. wire length = 1000 feet.

Do not

mix different models on same circuit as proper operation

may be impaired.

Name

System Sensor
Sentrol (GE)

Model

2W-B, 2WT-B, 1151, 2100, 2100T, 2151
429AT, 521BXT, 521B

Compatibility ID

S09A

Max #

20
20

Base