Elk Products ELK-M1G Installation And Programming Manual Download Page 47

Page: 47 / 72

M1G Installation and Programming

Page 47

Menu 14 - Wireless Setup

Press RIGHT arrow key to select this menu. Press UP or DOWN arrow keys to select
another menu. The ELK key backs up one menu level. To exit press the * or Exit key.

12345678901234567890123456789012123

1 4 - W i r e l e s s
Setup

There are four (4) submenus: 1-Receiver Options, 2-Xmitter Options, 3-Xmitter Enroll, and 4-Keyfob Event Definitions.
Use the UP or DOWN arrow keys to locate the desired submenu, then press the right arrow key to select. The Elk-
M1XRFTW Two-Way Receiver supports up to 144 of the Elk6000 series two-way wireless sensors (zones). Refer to
the M1XRFTW Installation Instructions for a listing of the compatible Elk6000 series sensors. Elk produces two other
models of “M1XRF” Wireless Receivers that support wireless sensors made by other companies.

NOTE: The M1 will voice announce a relative transmission level from 1 to 8 (8 being the highest level) at the time of
enrollment of each wireless sensor AND during the “Walk Test Area” function activated from the keypad user menus.

†

Not evaluated by UL

Wireless Submenu

Description

This submenu is for Receiver (Transceiver) options. To select this menu press the RIGHT
arrow key, or press the Up or Down arrow keys to scroll the submenus.

Burglary (non-fire) sensors. Sets the expiration timeout for zones assigned as Supervisory

Type 1. Default is 024 hours. Range is 001 to 255 hours. A sensor set for Supervisory Type 1

will be declared missing if it fails to check-in during this timeout period. Sub-menu 2:
Transmitter Opt 02 is location to the Supervisory TypesFire. (see below)

†

Fire sensors. Sets the expiration timeout of zones assigned as Supervisory Type 3. Default

is 004 hours. Range is 001 to 255 hours. A Type 3 sensor will be declared missing if it fails

to check-in during this timeout period.

For UL listed installations with the Elk-XRFTW Transceiver this option should be enabled.

This provides a trouble indication in the event of an attempt to jam the wireless frequency. And

in the event the M1XRFTW Transceiver ever become inoperable or missing the M1 will violate
all wireless unarmed burglar zones and trouble all wireless fire zones.

1234567890123456789012345678901212345

RO3:=024 Hours

Reg. Supervision

1234567890123456789012345678901212345

RO4:=004 Hours

Fire Supervision

1234567890123456789012345678901212345

WZn017 01: = No

Enable Transmitr

1234567890123456789012345678901212345

WZn017 02: = 0

Supervision Type

1234567890123456789012345678901212345

WZn017:Sel

Prg

Wireless Zone

1234567890123456789012345678901212345

1:Rec Sel

Prg

Receiver Options

123456789012345678901234567890121234

2:Xmit Sel

Prg

Transmitter Opt

This submenu is for specific transmitter (sensor) options. To select this menu press the
RIGHT arrow key, or press the Up or Down arrow keys to scroll to another submenu.

From the initial zone displayed, locate the desired wireless zone using the UP and DOWN

arrow keys. Press the RIGHT arrow key to select and program the displayed transmitter.

Displays if a transmitter is enabled or disabled. This option CANNOT be used to add a new

device. It can only be used to temporarily suspend or disabled an already enrolled device.
This will automatically be set to Yes when a new sensor is added via the enroll process.

This sets the Supervisory Type for each sensor. For Burglar (non-fire) sensors set the Type as
“1” = Reg. (Normal) Supervision. For Fire Sensors

†

set the Type as "3" = Fire Supervision.

For Keychain Remotes

†

(Fobs) or sensors that may be taken from the premises set the Type

as “0” = non supervised. See receiver selections R02 and R03 for supervision time values.
Valid values are: 0, 1, or 3 Factory default setting is “1” = Reg. (Normal) Supervision.

This is relevant to only a few select sensors. Factory default is No.

See the List of Elk 6000

Series Wireless Sensors to determine which transmitters use this option.

This is relevant to only a few select sensors. Factory default is No.

See the List of Elk 6000

Series Wireless Sensors to determine which transmitters use this option.

A User ID code may be assigned to wireless sensors like Keychain Remotes (Fobs). This ID

will be used in the M1 event log to identify the Fob that was used to arm or disarm the Control.
Valid range is 001 to 255. NOTE: Standard M1 User codes are 001 to 199.

This option (PIR Auto Restore) is not currently used by the M1XRFTW.

1234567890123456789012345678901212345

WZn017 04: = No

Enable Option 2

1234567890123456789012345678901212345

WZn017 03: = No

Enable Option 1

1234567890123456789012345678901212345

WZn017 05: = 001

Keyfob User ID

1234567890123456789012345678901212345

WZn017 06: = No