background image

 

definite image. 

21

 

Microscope Fixation Screw 

22

 

Accessories Mount 

Accept  the  model  R-900  Goldmann  applanation  tonometer  as  well  as  other 

accessories 

23

 

Horizontal Mark 
When  the  horizontal  center  of  the  patient’s  eye  is  in  line  with  this  mark,  the 
elevation of the microscope controlled by joystick is also in its center position. 

24

 

Forehead Belt   

25

 

Diffusion Lens 

  Used for observing and photographing at a low magnification, and for enlarging 

the illumination field. 

26

 

Lamp Cap 

27

 

Aperture Slit Height and Display Window 

28

 

Filter Selection Lever 
There are four filters for selection 

29

 

Aperture and Slit Height Control Knob 
Rotate  this  knob  to  adjust  the  spot  and  the  slit  height.  Swing  the  knob 
horizontally to revolve the slit.   

30

 

Fixation target 
Two kinds of fixation targets are available. One is for diopter adjustment to help 
the patient to see the target clearly while the other is an illuminated fixed spot. 

31

 

Reflecting Mirror 
Both long and short reflecting mirrors are provided. The long mirror is routinely 
used  for  most  examination  procedures.  The  short  mirror  is  used  when  the  long 
mirror interferes with the observation pathway, such as during funduscopy. 

32

 

Hruby Lens 

Used for observation of fundus and the posterior segment of vitreous body. 

33

 

Hruby Lens Holder   

34

 

Centering Knob 
Loosening the knob allows the illumination light to be moved from the center of 
the  vision  field  for  indirect  retro-illumination.  Fastening  the  knob  brings  the 
illumination light back to the center. 

35

 

Slit Width Control Knob 
The  slit  width  is  continuously  adjustable  within  the  range  from  0  to  9mm.  The 
marks on the left knob stand for the approximate value of the width.   

36

 

Illumination Inclination Lever   
Four 5

o

 inclination stops are available

up to 20

o

37 Brightness Control Connector 
 
 

Summary of Contents for ESL-7800

























Reviews: