manualshive.com logo in svg

ELGO Electric P8721-000-R SERIES, Manual, Page: 19 / 35

Share
Download
ELGO Electric P8721-000-R SERIES Manual Download Page 19

 
 
 

19 

 

R15 

Software Limit / End Limits Selection 

 

Software limits (R13 & R14) are active in accordance with the setting of R15/6 

 

R13/R14 Min/Max software limits 

 

 

                                      Fault Message 

Target < Limit R13

 =  04 

Target > Limit R14

 =  05 

 

 

xxxxx0

 Both software limits active 

xxxxx1 

Min software limit (R13) inhibited 

xxxxx2 

Max software limit (R14) inhibited 

xxxxx3 

Both software limits (R13&R14) inhibited 

 

 External limit switches can be connected to the St4/3 (backwards) and at St4/4 (forwards) 

 

xxxx0x

 Both limits inputs active 

xxxx1x

 Min limit input (St4/3) inhibited 

xxxx2x 

Max limit input (St4/4) inhibited 

xxxx3x 

Both software limit inputs (St4/3 St4/4) inhibited 

 

Notice: If these are not connected to limit switches they need to be connected Normally 

closed (i.e. linked out). 

 

R17 Display brightness

 

With the setting of this Parameter, the brightness of the displays can be altered. 

0= dark, 15 = max brightness. 

Summary of Contents for P8721-000-R SERIES




































Reviews:

No comments