background image

Dismantling and disposal | Technical data and dimensions 

WARNING 

Risk of injury due to electric current. 
Risk of electric shock. 

 

Separate power supply cables physically and discharge 

any energy accumulators still charged. After switching off 

the device, wait at least 5 minutes so that the motor can 

cool down and the voltage can be discharged from the 

capacitors. 

 

During disassembly work above head height, use 

suitable, inspected and structurally stable climbing aids. 

 

Work on the electrics may only be performed by 

personnel described in the section "Safety notes on 

electrical installation". 

Removal for scrap 

The international, national and regional laws and 

regulations prevailing at the time of scrapping the product 

must be observed. 
Ensure that materials and components are recycled, 

dismantled and separated properly in addition to observing 

the environmental and health hazards relating to recycling 

and disposal. 

CAUTION

Environmental damage in case of incorrect disposal 

 

Electrical scrap and electronic components must be 

handled as special waste and may only be disposed of by 

approved specialist companies. 

 

Groups of materials such as various types of plastics and 

metals must be separated before recycling/disposal. 

Disposal of electrical and electronic components 

The disposal and recycling of electrical and electronic 

components must be carried out in accordance with the 

relevant laws and national regulations. 

11  Conformity Declaration 

elero GmbH hereby declares that this product conforms 

with the applicable directives. For the full declaration of 

conformity, visit 

www.elero.com

 

12  Technical data and dimensions 

The technical data specified is subject to tolerance factors 

(according to applicable standards) and refer to an ambient 

temperature of 20 °C. 

12.1  InDrive M 

InDrive 

M30/1.6 RH 

Rated torque [Nm] 

30 

Rated speed [rpm] 

1.6 

Rated voltage [V] 

1 ~ 230 

Rated frequency [Hz] 

50 

Noiseless soft brake 

■ 

Rated current [A] 

0.52 

Rated power consumption 

[W] 

118 

Shaft diameter [mm] 

50 

Degree of protection 

(IP-Code) 

44 

Limit switch range (revolu-

tions) 

40 

Operating time (min. S2) 

Length C [mm] 

469 

Length D [mm] 

452 

Length E [mm] 

12 

Weight [kg] 

1.9 

Operating ambient tempera-

ture [°C] 

-20 to 70 

Protection class I

 

■ 

Conformity  

,   

-, - 

Item No. 

38 147.0001 

33

D

C

E

55

C

D

E

E

45

O

55

C

D

33

33

C

D

33

E

45

O

45

O

45

O

C

D

33

45

O

O

57,

5

E

C

D

33

45

O

O

57,

5

E

29

O

49

,5

O

49

,5

C

D

45

O

E

33

O

60,4

RolBasic Soprofen

Stator FE

C

D

E

Motorrohr

Rol/Sun/Vari

M6-k

381

364

elero=14

339

M10-k

391

374

RH=12

349

M6

446

429

SH=19

404

M10

466

449

424

M7/23 (120V)//M10/17 (120V)

486

469

444

M30

516

499

474

M20

526

509

484

M40/M50

546

529

504

RolTop M1,8/138 RH Neher

384493401

120

556

539

514

RolTop M1,8/138-868 RH Neher 384403406

120

RolBasic M6 Soprofen

643011902

481

464

12,6

438,5

RolBasic M10 Soprofen

643211902

481

464

12,6

438,5

RolBasic M20 Soprofen

643311902

506

489

12,6

464

D= C-17mm (halbe Kupplung)

Baugröße Typ

We reserve the right to make technical changes

elero GmbH

Antriebstechnik

Maybachstr. 30 

73278 Schlierbach

[email protected]

www.elero.com

Summary of Contents for InDrive M30/1.6 RH









Reviews: