elero InDrive M30/1.6 RH, Operating And Assembly Instructions Manual

Page: 7 / 8

5.6.9 Variant D: initial position freely adjustable,
end position at limit stop
Variant D: initial position freely adjustable, end
position at limit stop
①
Starting from a central slat position, press the
[ UP▲ ] button with the assembly cable until the slats
have reached the desired initial position.
The drive begins to travel, briefly stops and travels
further (for as long as the button remains pressed).
You can make corrections using the [
UP ▲ ] and
[
DOWN/CLOSE ▼
] buttons.
②
Press the [ DOWN/CLOSE ▼ ] button until the drive
stops automatically.
The initial position is set.
③
Press the [ DOWN/CLOSE ▼ ] button again until the
slats have reached the desired end position (travel
to limit stop).
The drive begins to travel, briefly stops, and
then travels further (for as long as the [DOWN/
CLOSE ▼ ] button remains pressed).
The drive switches off automatically when it reaches
the end position.
④
Press the [ UP ▲] button until the drive stops auto -
matically.
The end position is set.
Optional: Activate the release function for the end
position: See chapter 5.6.3
Adjustment of the variant D end positions is complete.
Fig. 10 End positions variant D:
6 Troubleshooting
Problem / Error Possible cause Remedial
action
• Drive stops
during travel
• End positions
are not set
• Drive is in
setting mode
• Configure end
positions
• Drive stops
after short time
• End position
has been pro-
grammed
• Stiff slats
• Set end po-
sition
• Check the
ease of move-
ment of the
slats
• Drive runs only
in one direction
• Faulty connec-
tion
• Check connec-
tion
• Drive does not
react
• No power
supply
• Temperature
limiter has
triggered
• Check mains
voltage
• Allow drive to
cool down
Problem / Error Possible cause Remedial
action
• End positions
cannot be
taught into the
drive
• Random travel
• Travel to end
position or limit
stop too short
• Delete end
positions,
re-programme
end positions
• Drive must
move, stop
briefly and
continue its
travel (as long
as a button
on the assem-
bly cable is
pressed).
Fig. 11 Troubleshooting for the InDrive M30/1.6 RH
7 Servicing
The InDrive M30/1.6 RH requires no maintenance.
8 Service/manufacturer's address
elero GmbH
Drive technology
Maybachstr. 30
73278 Schlierbach
Deutschland / Germany
Tel: +49 7021 9539-0
Fax: +49 7021 9539-212
info@elero.de
www.elero.com
Please visit our website if you require a contact partner
outside Germany.
9 Repairs
Please contact your specialist if you have any questions.
Please always provide the following information:
• Item number and designation on the type plate
• Type of fault
• Accompanying conditions
• Your own theories regarding the cause of the problem
10 Disassembly and disposal
After unpacking, dispose of the packaging in accordance
with the valid regulations.
Dispose of the product in accordance with the relevant
regulations when you no longer need it.
Environmental information
No superfluous packaging materials have been used. The
packaging can be easily separated into three material
types: cardboard (box), polystyrene (padding) and
polyethylene (bag, protective foam).
The device is made of materials that can be reused if
dismantled by a specialist company. Please note the local
regulations on disposal of packaging materials and old
appliances.
On disassembly, additional dangers must be reckoned with,
which do not occur during operation.
Before disassembling the drive the system is to be
mechanically secured. The drive must not be forcibly
disconnected from the system.
© elero GmbH EN | 7
Setting the end positions and release | Troubleshooting