Electrothermal MC810B MKII Instruction Book Download Page 24

Page: 24 / 24

Page 24 of 24 M6493 Issue 10.3

13. EC DECLARATION OF CONFORMITY.

CE marked products and associated accessories covered by this Instruction book conform to
the essential requirements of the following directives:

EMC Directive.

Low Voltage Directive.

A full copy of the EC Declaration / Conformity document can be obtained from the manufacture
at the email address :

[email protected]

Bibby Scientific Limited.

Beacon Road,
Stone,
Staffordshire ST15 0SA,
Great Britain.

Tel: +44(0)1785 812121
Fax: +44(0)1785 810405

•

General enquiries :

[email protected]

•

Order enquiries :

[email protected]

•

Technical support :

[email protected]

•

www.electrothermal.com

For the America’s and Canada, contact:
Techne Incorporated,

3 Terri Lane,

Suite 10 Burlington, NJ 08016 USA.

Toll free:800-225-9243Tel: 609-589-2560
Fax: 609-589-2571
Email:

[email protected]

Http

www.techneusa.com

Part of the Bibby Scientific Group



Distributors Stamp

Summary of Contents for MC810B MKII

























Search results

Summary of Contents for MC810B MKII

Reviews:

Related manuals for MC810B MKII

Brands by name

Popular brands

Electrothermal MC810B MKII, Instruction Book

Search results

Summary of Contents for MC810B MKII

Reviews:

Related manuals for MC810B MKII

Brands by name

Popular brands